Pass the Exin EPI Data Centre CDCS Questions and answers with CertsForce

To calculate the cooling airflow requirement for ICT equipment, you can use the formula:

CFM=Power (kW)×3160ΔT(°F)\text{CFM} = \frac{\text{Power (kW)} \times 3160}{\Delta T (\text{°F})}CFM=ΔT(°F)Power (kW)×3160​

For equipment consuming 6 kW with a Delta-T of 20°F:

CFM=6×316020=948≈1,000 CFM\text{CFM} = \frac{6 \times 3160}{20} = 948 \approx 1,000 \, \text{CFM}CFM=206×3160​=948≈1,000CFM

Detailed Explanation:

This formula provides an estimate of the cubic feet per minute (CFM) of air required to cool the equipment based on its power consumption and the temperature difference (Delta-T) between intake and exhaust. The Delta-T represents the cooling effectiveness of the airflow.

EPI Data Center Specialist References:

EPI recommends using this calculation for determining airflow requirements in data centers, ensuring that cooling systems are adequately sized to maintain equipment within safe temperature limits.

ASHRAE recommends temperature and humidity be measured in the cold aisle, in front of racks, at approximately 1.5 m above the floor (average human working height) and 0.3–0.5 m from the rack face. This location captures the environmental conditions experienced at the IT equipment air intake, while still representing facility-level conditions (not single device-level).

Option A and C (at 50 mm intake/rear) are too close to individual servers and suited only for rack-level monitoring, not facility monitoring.

Option D (rear measurement) reflects exhaust air, not intake, and thus cannot be used to control environmental setpoints.

Maintaining measurement at standardized facility locations allows comparisons against ASHRAE’s recommended and allowable ranges (18–27 °C for Class A1 environments, 40–60% RH).

The aisle pitch is the total width of a rack row plus cold aisle plus rack row. For 1.0 m racks on each side with cold aisle containment, ASHRAE and TIA-942 recommend the 7-tile rule (each tile ~0.6 m). This ensures enough width for equipment clearance, airflow distribution, and human access.

5-tile pitch is too narrow, restricting containment effectiveness.

8–10 tiles may be used in some hyperscale layouts but are not standard for 1 m racks.

Thus, the correct design recommendation is the 7 tiles pitch rule.

IEC 62040 defines UPS topologies:

VFD: Line-interactive; dependent on mains.

VI: Stabilizes voltage but not frequency.

VFI: Double-conversion online; fully isolates output from mains fluctuations.

Data centers require continuous, clean, and stable power. VFI is the only topology that protects against both voltage and frequency disturbances, meeting ANSI/TIA-942 Rated-3/4 requirements.

Thus, VFI is the ideal UPS class.

ANSI/TIA-942 requires a risk assessment–based approach to physical security; ballistic protection is not mandated but may be justified by threat analysis.

A is incomplete (it may still be required by risk).

The cooling capacity of a raised floor tile is primarily influenced by the percentage of surface opening, the obstruction caused by the supporting construction, the pressure under the raised floor, and the damper construction. These factors dictate how much airflow can pass through the tile and how effectively cool air is distributed to the equipment in the data center.

Detailed Explanation:

The percentage of surface opening on a floor tile affects how much air can flow through, with larger openings allowing more airflow. Supporting structures beneath the floor can obstruct airflow, reducing cooling efficiency. Pressure under the raised floor impacts the velocity and volume of air that moves through the tile. Additionally, if dampers are installed, they control the airflow rate, which can be adjusted to meet specific cooling needs for the area.

EPI Data Center Specialist References:

EPI guidance on airflow management under raised floors emphasizes these factors as critical for effective cooling, especially in high-density areas. Ensuring unobstructed and adequate airflow helps maintain consistent cooling across equipment.

High dust levels in a computer room are often due to improperly fitted floorboards. When floorboards are not securely installed or do not fit tightly, they allow dust and particles from the subfloor to enter the room. In a data center, this can lead to high levels of dust that affect air quality and equipment performance.

Detailed Explanation:

Raised floors in data centers can accumulate dust and debris, especially if the floorboards are not properly sealed. Loose or improperly fitted floorboards allow contaminants from the subfloor to enter the data center environment, increasing the dust levels over time. Proper installation and maintenance of floor panels are essential to prevent dust infiltration and maintain clean conditions.

EPI Data Center Specialist References:

EPI training emphasizes proper flooring installation and maintenance to control air quality within data centers. Correctly fitted floorboards prevent dust accumulation from the subfloor, which helps protect sensitive equipment and maintains a cleaner environment.

Raised floors must not be installed flush against perimeter walls. Buildings expand, contract, and shift due to thermal expansion (hygrothermal movement), structural settlement, and seismic activity. If the raised floor is rigidly connected to the walls, this movement transfers directly into the raised floor grid, causing buckling, cracking, or tile misalignment.

Industry standards (e.g., CISCA – Ceilings & Interior Systems Construction Association guidelines) require leaving a small perimeter gap (typically 1–2 cm) between raised floor tiles and walls. This gap is then sealed with flexible firestops or brush gaskets to control air leakage while preserving movement tolerance.

Therefore, the correct practice is to leave a separation space, making answer C correct. Options A and D restrict this requirement incorrectly, while B is factually wrong (sealing against the perimeter is not allowed).

To determine the required capacity of the battery bank for the 15-minute runtime at full load, one must know the total power requirement that the battery bank must supply. The specifications provided include most of the necessary details, such as rated power, input voltage, battery voltage, and discharge voltage. However, one critical piece of information is missing: the UPS efficiency.

Detailed Explanation:

In a data center UPS system, the battery bank is designed to supply power for a set duration when there is an input power failure. The UPS efficiency affects the actual power the UPS can deliver to the load compared to the power it draws from the batteries. The efficiency factor is necessary to accurately calculate the required capacity of the battery bank since it determines how much input power is needed from the batteries to supply the load at full capacity. The formula typically used to determine battery capacity involves factoring in UPS efficiency, as it allows you to understand the losses within the UPS system.

If UPS efficiency is not considered, there would be an inaccurate estimation of the actual power needed from the batteries. For instance, if a UPS has 90% efficiency, only 90% of the power drawn from the batteries reaches the load. Without knowing this efficiency, it is not possible to calculate the battery bank size accurately, as you cannot accurately estimate the losses within the UPS itself.

EPI Data Center Specialist References:

According to EPI Data Center Specialist training, understanding the UPS efficiency is essential for battery sizing. Without it, the calculations could lead to either undersizing or oversizing the battery bank, which affects both reliability and cost-effectiveness of the UPS system. The EPI Data Center Specialist course emphasizes that battery sizing must account for all losses within the UPS system, with efficiency being a primary factor in these calculations.

Attenuation is the logarithmic ratio between input and output signals. For power, we use 10 log; for voltage or current, 20 log. Since EMF shielding is measured as field strength (V/m or A/m), power relationship is proportional to the square of field. Thus the correct attenuation calculation for shielding effectiveness is:

A black text on a white background AI-generated content may be incorrect.

where:

M = maximum permissible field strength

R = measured field strength after shielding

This ensures the shield reduces field intensity to below allowable limits.