Cisco 350-601 Exam Questions Free Practice Test

Viewing page 4 out of 12 pages

Viewing questions 31-40 out of questions

Questions # 31:

Question # 31

Refer to the exhibit. The MDS-EDGE-Switch and MDS-Core-Switch are configured with NPV and NPIV features The FLOGI from Cisco UCS is received by the MDS-Core-Switch on interface fc1/2. An engineer tried to move all traffic between the MDS-EDGE-Switch and MOS-Core-Switch from interface fc 1/2 to fc1/3, but the attempt failed. Which set of actions completes the configuration?

Options:

Disable the NPV feature in the MDS-EDGE-Switch.Re-enable the NPV feature.Disable interface fc1/1.

Disable the NPIV feature in the MDS-EDGE-Switch.Re-enable the NPIV feature.Disable interface fc1/3.

Shut down fc1/1 in the MDS-EDGE-Switch.Re-apply the command.Enable interface fc1/1.

Shutdown fc1/3 in the MDS-EDGE-Switch.Re-apply the command.Enable interface fc1/3.

Expert Solution

Questions # 32:

Question # 32

Refer to the exhibit. An engineer configured OSPF on a Cisco Nexus 9000 Series Switch. The engineer planned to authenticate OSPF messages on interface Eth1/1 and use md5 for authentication and encrypt password using 3DES. Which command snippet must be used to resolve the issue?

Options:

ip ospf authentication md5ip ospf authentication-key 3 P@ssw01

ip ospf authentication message-digestip ospf message-digest-key 2 md5 3 P@ssw01

ip ospf authentication md5ip ospf message-digest-key 2 md5 3 P@ssw01

ip ospf authentication message-digestip ospf authentication-key 3 md5 P@ssw01

Expert Solution

Questions # 33:

A network engineer repeatedly saves a configuration on Catalyst switches to NVRAM using the write memory command. What action should be taken to implement the same action on Nexus switches?

Options:

Use the exit command to leave the configuration mode and save the configuration automatically.

Use the write memory command to save the configuration.

Use the alias command to use the write memory command.

Use the wri command to use the copy running-config startup-config command.

Expert Solution

Questions # 34:

An engineer must assign a device alias of Marketing to a Fibre Channel port that has a worldwide name of 21:00:00:00:11:11:22:22 on a Cisco MDS 9000 Series Switch. Which two commands accomplish this goal? (Choose two.)

Options:

vsan database

device-alias database

device-alias name Marketing pwwn 21:00:00:00:11:11:22:22

device-alias name Marketing wwn 21:00:00:00:11:11:22:22

device-alias rename wwn Marketing

Expert Solution

Questions # 35:

Which Feature differentiates Intersight Managed Mode from UCSM Managed Mode when configuring and managing a Cisco UCS-X Series Modular System?

Options:

It decouples the management software from the infrastructure.

It consolidates all the events and alerts from the fabric interconnects.

lt supports up to 200 servers in the same UCS domain

It provides full visibility of the UCS chassis components

Expert Solution

Questions # 36:

Question # 36

Refer to the exhibit An engineer must resolve a connectivity issue on a Cisco 9000 Senes Switch that was configured by using Ansible The switch must be configured to meet these requirements •Interface G*gabitethemet0/1 must be a member of VLAN 10 in access mode •Interface G*gabetethernet0/2 must allow VLANs 10 and 20 in trunk mode, with native VLAN 20

Which set of actions must be taken to meet these criteria?

Options:

Configure interface G»gabitethernet0/2 in trunk mode Assign interface GigabitethernetO/1 to VLAN 10

Configure interface Gigabitethernet0/1 in access mode Assign interface GigabitethernetO/1 to VLAN 10

Configure interface GigabttethemetOV 1 in trunk mode Assign interface GigabitethernetO/2 to VLAN 20

Configure interface GigabitethernetQ/2 in access mode Assign interface G»gabitethernet0/2 to VLAN 20

Expert Solution

Questions # 37:

What is the impact of an electronic programmable logic device upgrade on a Cisco MDS 9000 Series Director Switch with dual supervisors?

Options:

A manual reboot is required for each supervisor.

Nondisruptive upgrades without traffic interruptions can be performed.

The upgrade is aborted if any module is unsupported.

A complete system reboot is triggered.

Expert Solution

Questions # 38:

An engineer must authenticate OSPF on interfaces of me Cisco Nexus 9000 Senes Switch so mat

eth1/1 uses clear text password

etht ' 2 uses encrypted md5 password

Drag and drop the commands from the bottom onto the boxes in the code to complete me configuration Not all commands are used.

Question # 38

Expert Solution

Questions # 39:

DNS server with IP address 192.168.1.1 is deployed in a data center A network engineer must configure a Cisco UCS Fabric Interconnect to use this DNS. Which configuration should be applied?

Options:

ficl-mgmt-A# scope systemficl-mgmt-A /system # create dns 192.168.1.1ficl-mgmt-A /system* # commit-buffer

ficl-mgmt-A# scope fabric-interconnect aficl-mgmt-A /fabric-interconnect # set name 192.168.1.1ficl-mgmt-A /fabric-interconnect # scope system

ficl-mgmt-A /system # commit-bufferficl-mgmt-A# scope fabric-interconnect aficl-mgmt-A /fabric-interconnect # set name 192.168.1.1

ficl-mgmt-A /fabric-interconnect* # commit-bufferficl-mgmt-A# scope systemficl-mgmt-A /system # scope servicesficl-mgmt-A /system/services # create dns 192.168.1.1ficl-mgmt-A /system/services* # commit-buffer

Expert Solution

Questions # 40:

A network engineer must enable port security on all cisco MDS series switches in the fabric. The requirement is to avoid the extensive manual configuration of the switch ports. Which action must be taken to meet these requirements?

Options:

Activate CFS distribution and the auto-learning port security feature.

Activate CFS distribution and the auto-learning port security feature on a per-VSAN basis.

Enable the auto-learning port security feature on a per-VSAN basis.

Enable the auto-learning port security feature.

Expert Solution

Viewing page 4 out of 12 pages

Viewing questions 31-40 out of questions

Pre-Summer Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: force70

Pass the Cisco CCNP Data Center 350-601 Questions and answers with CertsForce