Pass the CWNP CWNA CWNA-109 Questions and answers with CertsForce

The BSSID (Basic Service Set Identifier) is typically mapped to an AP’s MAC address if a single BSS is implemented. The BSSID is a unique identifier that distinguishes one BSS from another within the same RF medium. It is usually derived from the MAC address of the AP’s radio interface, but it can also be manually configured or randomly generated by some vendors. The BSSID is used by client stations to associate with an AP and to send and receive frames within a BSS. References: , Chapter 1, page 24; , Section 1.2

S1G is one of the 802.11 PHYs that is more likely to be used in an industrial deployment but not likely to be used in standard office deployments. This is because S1G stands for Sub-1 GHz, which means it operates in the frequency bands below 1 GHz, such as 900 MHz and 868 MHz. These bands offer better penetration and range than the higher frequency bands used by other 802.11 PHYs, such as 2.4 GHz and 5 GHz. This makes S1G suitable for industrial applications that require robust and reliable wireless communication in harsh environments, such as factories, warehouses, mines, and smart grids. S1G also supports low-power and low-data-rate devices, such as sensors, actuators, and meters, which are common in industrial Internet of Things (IoT) scenarios. VHT, OFDM, and HT are other 802.11 PHYs that are more commonly used in standard office deployments, as they offer higher data rates and capacity than S1G, but have lower range and penetration. References: CWNA-109 Study Guide, Chapter 3: Radio Frequency Technologies, page 751

Calibrating the floor plan is what you must do before gathering survey data after the floor plan is imported when using a site survey tool for post-implementation validation. A site survey tool is a software application that can run on a laptop, tablet, smartphone, or other device that has a Wi-Fi adapter and a GPS receiver. A site survey tool can scan the wireless environment and collect information about the detected access points and client stations, such as their SSID, BSSID, channel, signal strength, security, and data rate. A site survey tool can also measure and display various metrics of network performance, such as throughput, jitter, packet loss, delay, and SNR. A site survey tool can also use a floor plan to visualize the wireless coverage and quality in different locations on a map. A floor plan is an image file that shows the layout and dimensions of a building or an area where the WLAN is deployed. A floor plan can be imported from various sources, such as a CAD file, a PDF file, an image file, or a Google Maps screenshot. After importing a floor plan into a site survey tool, it is necessary to calibrate the floor plan before gathering survey data. Calibrating the floor plan means adjusting the scale and orientation of the floor plan to match the actual size and direction of the area. Calibrating the floor plan can be done by using a reference point or a reference line that has a known distance or angle in the real world. Calibrating the floor plan ensures that the survey data is accurate and consistent with the physical environment. References: 1, Chapter 7, page 290; 2, Section 4.3

The tool described is a WLAN (Wireless Local Area Network) scanner tool. WLAN scanner tools are designed to provide information about the wireless networks in a given area, including:

Signal Strength: They show the signal strength of all access points (APs) in the vicinity, which is crucial for understanding the coverage area and potential interference.

SSID Visualization: These tools display the SSIDs (Service Set Identifiers) of available networks, allowing users to identify different wireless networks easily.

Security Settings Information: WLAN scanner tools often show the type of security implemented on each network, such as WPA2, WEP, etc.

Frequency Band Filtering: They allow users to filter and view networks based on the frequency band (2.4 GHz or 5 GHz), which is useful for analyzing network distribution and planning.

While protocol analyzers, site survey utilities, and spectrum analyzers are also used in wireless networking, their functions are distinct from what is described:

Protocol Analyzers are more sophisticated and are used to capture and analyze network traffic.

Site Survey Utilities are used to map signal coverage and plan network layouts, often with more advanced features for detailed site surveys.

Spectrum Analyzers provide a detailed view of the frequency spectrum and non-Wi-Fi interference but don't typically focus on SSIDs or security settings.

Thus, the correct answer is D, a WLAN scanner tool, based on the functionalities described.

USB 3 devices in the user’s work area are the most likely cause of this interference when using a spectrum analyzer to look for non-Wi-Fi interference sources. A spectrum analyzer is a tool that measures and visualizes the radio frequency activity and interference in the wireless environment. A spectrum analyzer can show the spectrum usage and energy levels on each frequency band or channel and help identify and locate the sources of interference. Interference is any unwanted signal that disrupts or degrades the intended signal on a wireless channel. Interference can be caused by various sources, such as other Wi-Fi devices, non-Wi-Fi devices, or natural phenomena. Interference can affect WLAN performance and quality by causing signal loss, noise, distortion, or errors. USB 3 devices are non-Wi-Fi devices that use USB 3.0 technology to transfer data at high speeds between computers and peripherals, such as hard drives, flash drives, cameras, or printers. USB 3 devices can generate electromagnetic radiation that interferes with Wi-Fi signals in the 2.4 GHz band, especially when they are close to Wi-Fi devices or antennas. USB 3 devices can cause significant interference across the entire 2.4 GHz band (not on a few select frequencies) within the desktop area of a user’s workspace, but the interference disappears quickly after just 2 meters. This is because USB 3 devices emit broadband interference that affects all channels in the 2.4 GHz band with a high intensity near the source but a low intensity at a distance due to attenuation. The other options are not likely to cause this interference pattern when using a spectrum analyzer to look for non-Wi-Fi interference sources. Bluetooth devices in the user’s work area are non-Wi-Fi devices that use Bluetooth technology to communicate wirelessly between computers and peripherals, such as keyboards, mice, headphones, or speakers. Bluetooth devices can cause interference with Wi-Fi signals in the 2.4 GHz band, but they use frequency hopping spread spectrum (FHSS) technique that changes frequencies rapidly and randomly within a range of 79 channels. Therefore, Bluetooth devices do not cause significant interference across the entire 2.4 GHz band (not on a few select frequencies), but rather intermittent interference on some channels at different times. Excess RF energy from a nearby AP is not a non-Wi-Fi interference source but rather a Wi-Fi interference source that occurs when an AP transmits more power than necessary for its coverage area. Excess RF energy from a nearby AP can cause co-channel interference (CCI) with other APs or client devices that use the same channel within range of each other. CCI reduces performance and capacity because it causes contention and collisions on the wireless medium,

The beamwidth of an RF antenna is the angular measure of how wide the main lobe of radiation is. The main lobe is the area where the signal strength is highest and most concentrated. The beamwidth is calculated at the points where the main lobe decreases power by 3 dB, which means it is half of the maximum power. The beamwidth can be measured in both horizontal and vertical planes, depending on how the antenna is oriented. The horizontal beamwidth is also called azimuth, while the vertical beamwidth is also called elevation. The beamwidth patterns on an antenna polar chart indicate how the RF energy is distributed in different directions. References: 1, Chapter 2, page 66; 2, Section 2.3

WLAN bridges must use a channel with acceptable SNR at both transceivers to maintain the desired data rate bi-directionally. A WLAN bridge is a device that connects two or more networks using the 802.11 protocol. A WLAN bridge must have a clear and strong signal between the two endpoints to ensure reliable and fast data transmission. The signal-to-noise ratio (SNR) is a measure of the quality of the signal, which depends on the distance, interference, obstacles, and antenna gain between the transceivers. A higher SNR means a better signal quality and a higher data rate. A lower SNR means a worse signal quality and a lower data rate. Therefore, a WLAN bridge must use a channel with acceptable SNR at both transceivers to maintain the desired data rate bi-directionally1.

The solution that you recommend is an Overlay WLAN monitoring solution. An Overlay WLAN monitoring solution is a system that uses dedicated sensors or probes to monitor the WLAN performance over time. The sensors are deployed throughout the WLAN coverage area and collect data on various metrics such as signal strength, noise level, channel utilization, interference, throughput, latency, packet loss, and QoS. The sensors send the data to a centralized server or appliance that analyzes the data and provides a single pane of glass for administration and monitoring of the solution. An Overlay WLAN monitoring solution can help to detect and troubleshoot WLAN issues, optimize WLAN performance, and generate reports and alerts. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 538; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 508.

The term used to describe the problem in this configuration is Co-Channel Interference (CCI)1. CCI occurs when multiple access points are on the same or overlapping channels, causing interference and degradation in network performance1. In this case, one AP is on channel 1 and the other is on channel 2, which are overlapping channels, leading to CCI1.

The FCS (Frame Check Sequence) is appended to the end of each 802.11 data frame after the payload. The FCS is a 4-byte field that contains a CRC-32 (Cyclic Redundancy Check) value that is calculated based on the contents of the MAC header and the payload of the frame. The FCS is used by the receiver to verify the integrity of the frame and to detect any errors or corruption that may have occurred during transmission. If the FCS does not match with the expected value, the frame is discarded by the receiver. References: , Chapter 4, page 139; , Section 4.2