Pass the CWNP CWNA CWNA-109 Questions and answers with CertsForce

A BSS (Basic Service Set) is a WLAN use case that represents an 802.11-based network that uses an AP (Access Point) and has several connecting clients. The AP acts as a central point of coordination and communication for the clients, which can include iPhones, iPads, laptops, desktops, or any other devices that have Wi-Fi capabilities. A BSS can be identified by a unique BSSID (Basic Service Set Identifier), which is usually the MAC address of the AP’s radio interface. A BSS can also be associated with an SSID (Service Set Identifier), which is a human-readable name that identifies the network. References: , Chapter 1, page 23; , Section 1.1

OFDM (Orthogonal Frequency Division Multiplexing) is the physical layer specification (PHY) that VHT capable devices must be backward compatible with according to the IEEE 802.11-2012 standard. VHT (Very High Throughput) is a PHY and MAC enhancement that is defined in the IEEE 802.11ac amendment and is also known as Wi-Fi 5. VHT operates only in the 5 GHz band and uses features such as wider channel bandwidths (up to 160 MHz), higher modulation schemes (up to 256-QAM), more spatial streams (up to eight), multi-user MIMO (MU-MIMO), beamforming, and VHT PHY and MAC enhancements. VHT can achieve data rates up to 6.9 Gbps.

According to the IEEE 802.11-2012 standard, VHT capable devices must be backward compatible with devices using OFDM PHY, which is defined in the IEEE 802.11a amendment and is also used by IEEE 802.11g, IEEE 802.11n, and IEEE 802.11h amendments. OFDM operates in both the 2.4 GHz and 5 GHz bands and uses features such as subcarriers, symbols, guard intervals, and OFDM PHY and MAC enhancements. OFDM can achieve data rates up to 54 Mbps.

Backward compatibility means that VHT capable devices can interoperate with OFDM devices on the same network by using common features and parameters that are supported by both PHYs. For example, VHT capable devices can use a channel bandwidth of 20 MHz, a modulation scheme of BPSK, QPSK, or 16-QAM, one spatial stream, no beamforming, and OFDM PHY and MAC headers when communicating with OFDM devices. Backward compatibility also means that VHT capable devices can fall back to OFDM mode when the signal quality or SNR is too low for VHT mode. References: 1, Chapter 3, page 123; 2, Section 3.2

OFDMA is a new modulation scheme introduced in 802.11ax that allows multiple users to share the same channel by dividing it into smaller subchannels called resource units (RUs). This improves the efficiency and capacity of the WLAN by reducing contention and overhead. However, to use OFDMA, both the AP and the client must support 802.11ax and negotiate the parameters of the subchannel allocation. Therefore, the customer needs to upgrade the clients that require OFDMA to 802.11ax devices12.

The other options are not correct because they do not reflect the reality of OFDMA. Option B is incorrect because OFDMA is a mandatory feature of 802.11ax for both downlink and uplink transmissions, and all 802.11ax APs must support it1. Option C is incorrect because OFDM and OFDMA are different modulation schemes, and OFDM does not allow multiple users to share the same channel. Option D is incorrect because 802.11ac devices cannot support OFDMA through driver upgrades, as they lack the hardware and firmware capabilities to do so2.

The feature of 802.11ax (HE) that provides this functionality is OFDMA. OFDMA stands for Orthogonal Frequency Division Multiple Access and is a technology that allows multiple devices to communicate simultaneously on the same channel in the same BSS. OFDMA works by dividing a channel into smaller subchannels called Resource Units (RUs), which are composed of groups of subcarriers or tones. Each RU can be assigned to a different device based on its bandwidth requirement and signal quality. This way, OFDMA can increase the efficiency and capacity of the channel by reducing overhead, contention, and latency. OFDMA can also support both uplink and downlink multi-user transmissions using trigger frames and buffer status reports. 6 GHz support, TWT, and Wi-Fi-LTE are not features of 802.11ax that provide this functionality. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 226; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 216.

An isotropic radiator is a theoretical point source of electromagnetic radiation that radiates equally in all directions. It has no physical dimensions and no preferred direction of radiation. It is used as a reference for antenna gain because it represents the ideal case of a perfect omnidirectional antenna12

Antenna gain is a measure of how well an antenna concentrates its radiated power in a certain direction. It is expressed in decibels (dB) relative to a reference antenna. When the reference antenna is an isotropic radiator, the antenna gain is denoted by dBi, which stands for decibels relative to isotropic12

For example, an antenna with a gain of 3 dBi means that it radiates 3 dB more power in its main direction than an isotropic radiator would. Conversely, an antenna with a gain of -3 dBi means that it radiates 3 dB less power in its main direction than an isotropic radiator would12

Elevators are a common building item that frequently causes RF shadow and must be accounted for in coverage plans. RF shadow is a term that describes an area where wireless signals are blocked or significantly weakened by an obstacle or an object that absorbs or reflects RF energy. RF shadow can cause lack of coverage or poor performance in a WLAN because wireless devices in those areas may not be able to communicate with access points or other devices. RF shadow can be mitigated by adjusting access point placement, antenna orientation, transmit power level, or channel selection to avoid or overcome the obstacle or object that causes it. Elevators are a common building item that frequently causes RF shadow because they are made of metal and they move up and down within a shaft. Metal is a material that has high attenuation and reflection values, which means it can block or bounce off wireless signals very effectively. A moving elevator can create dynamic RF shadow that changes depending on its position and direction. Therefore, elevators must be accounted for in coverage plans to ensure adequate WLAN coverage and performance throughout the facility. The other options are not common building items that frequently cause RF shadow or must be accounted for in coverage plans. Wooden doors are not likely to cause RF shadow because they are made of wood, which is a material that has low attenuation and reflection values, which means it can pass through or slightly weaken wireless signals. Carpeted floors are not likely to cause RF shadow because they are made of fabric, which is a material that has low attenuation and reflection values, which means it can pass through or slightly weaken wireless signals. Cubicle partitions are not likely to cause RF shadow because they are made of thin plastic or cardboard, which are materials that have low attenuation and reflection values, which means they can pass through or slightly weaken wireless signals. References: CWNA-109 Study Guide, Chapter 13: Wireless LAN Site Surveys - Types & Processes , page 433

 The frame type that is used to reserve the wireless medium for the transmission of high data rate frames that may not be understood by all clients connected to the BSS is RTS. RTS stands for Request to Send and is a control frame that is sent by a station to request access to the medium for a specified duration. The RTS frame contains the source and destination MAC addresses, as well as a Network Allocation Vector (NAV) value that indicates how long the medium will be occupied. The destination station responds with a Clear to Send (CTS) frame that echoes the NAV value and grants permission to the source station. All other stations in the BSS hear either the RTS or CTS frame and update their NAV timers accordingly, deferring their transmissions until the medium is free. The RTS/CTS mechanism can be used to prevent hidden node problems, reduce collisions, and protect high data rate frames that use features such as 802.11n or 802.11ac that may not be compatible with legacy stations. ACK, Beacon, and PS-Poll are not used to reserve the medium for high data rate frames. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 112; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 102.

Return loss is a measure of how well the components of an RF system are matched in terms of their impedance. Impedance is the opposition to the flow of alternating current in a circuit, and it depends on the frequency, resistance, capacitance, and inductance of the components. When the impedance of the source, the transmission line, and the load are not equal, some of the power is reflected back to the source, causing a loss of forward power. This loss is expressed in decibels (dB) as return loss. The higher the return loss, the lower the reflection and the better the impedance matching. Conversely, the lower the return loss, the higher the reflection and the worse the impedance matching.

VSWR (Voltage Standing Wave Ratio) is another way of expressing the same concept. It is the ratio of the maximum voltage to the minimum voltage along a transmission line due to the interference of the incident and reflected waves. A VSWR of 1:1 means that there is no reflection and perfect impedance matching. A VSWR higher than 1:1 means that there is some reflection and impedance mismatch. The higher the VSWR, the higher the reflection and the lower the return loss.

Therefore, a significant impedance mismatch between components in an RF system will cause high reflection, high VSWR, and low return loss.

WPA2 (Wi-Fi Protected Access 2) is a security certification program developed by the Wi-Fi Alliance to secure wireless computer networks. It is important to understand the following:

WPA2 and the 802.11 Standard: While WPA2 is based on elements of the 802.11i amendment to the 802.11 standard, it is not itself a standard but rather a certification to ensure devices comply with certain security criteria, including the correct implementation of CCMP (Counter Mode Cipher Block Chaining Message Authentication Code Protocol) and AES (Advanced Encryption Standard).

CCMP/AES Implementation: WPA2 enhances the security of wireless networks by using CCMP for encryption, which is based on AES, a robust encryption algorithm. This represents a significant security improvement over WEP (Wired Equivalent Privacy) and WPA (Wi-Fi Protected Access) that used TKIP (Temporal Key Integrity Protocol).

WPA vs. WPA2: WPA was the interim security enhancement over WEP, utilizing TKIP for encryption. WPA2, however, moved to the more secure AES-based encryption method. Contrary to option C, WPA2 does not enhance security by using TKIP; it uses CCMP/AES.

Therefore, option B correctly describes WPA2 as a certification program ensuring devices properly implement the more secure CCMP/AES encryption methods.