Pass the CompTIA CompTIA Network+ N10-009 Questions and answers with CertsForce

A warm site is a compromise between a hot site and a cold site, providing a balance between cost and recovery time. It is partially equipped with the necessary hardware, software, and infrastructure, allowing for a quicker recovery compared to a cold site but at a lower cost than a hot site.

Recovery Time: Warm sites can be operational within hours to a day, making them suitable for non-critical applications that can tolerate short downtimes.

Cost-Effectiveness: Warm sites are more economical than hot sites as they do not require all systems to be fully operational at all times.

Network References:

CompTIA Network+ N10-007 Official Certification Guide: Discusses disaster recovery strategies and the different types of recovery sites.

Cisco Networking Academy: Provides training on disaster recovery planning and site selection.

Network+ Certification All-in-One Exam Guide: Explains the characteristics of hot, warm, and cold sites and their use cases in disaster recovery planning.

Warm sites offer a practical solution for maintaining business continuity for non-critical applications, balancing the need for availability with cost considerations.

BGP (Border Gateway Protocol) is used for routing data between different ISPs, making it essential for the functioning of the internet. Its primary use is for exchanging routing information between autonomous systems, especially different ISPs. Preventing loops within a LAN ishandled by protocols like Spanning Tree Protocol (STP), while improving reconvergence times and sharing routes with a Layer 3 switch are functions of other protocols or internal mechanisms.

Speed Mismatches: If NICs are set to different speeds (e.g., 100 Mbps on one side and 1 Gbps on the other), performance will degrade. Ensuring consistent speed settings between devices is crucial for optimal performance.

Load balancer settings (B): Applies to server load distribution, not endpoint speed.

Flow control settings (C): Can affect performance but is secondary to speed mismatches.

Infrastructure cabling grade (D): Relevant if the cables are unsuitable for gigabit speeds, but speed settings should be checked first.

Port 587 is used for secure email submission. This port is designated for message submission by mail clients to mail servers using the SMTP protocol, typically with STARTTLS for encryption.

Port 25: Traditionally used for SMTP relay, but not secure and often blocked by ISPs for outgoing mail due to spam concerns.

Port 110: Used for POP3 (Post Office Protocol version 3), not typically secured.

Port 143: Used for IMAP (Internet Message Access Protocol), which can be secured with STARTTLS or SSL/TLS.

Port 587: Specifically used for authenticated email submission (SMTP) with encryption, ensuring secure transmission of email from clients to servers.

Network References:

CompTIA Network+ N10-007 Official Certification Guide: Discusses email protocols and ports, including secure email transmission.

Cisco Networking Academy: Provides training on securing email communications and the use of appropriate ports.

Network+ Certification All-in-One Exam Guide: Explains email protocols, ports, and security considerations for email transmission.

Secure Shell (SSH) is a protocol used to securely access remote devices over an unsecured network. It provides encrypted command-line access and is a lightweight and secure method of remote administration.

A. Site-to-site VPN connects entire networks, not just a single host.

B. Telnet is not secure; it transmits data (including credentials) in plaintext.

C. Console access is direct via serial cable, not remote.

???? Reference:

CompTIA Network+ N10-009 Official Objectives: 2.6 – Configure and troubleshoot remote access.

These four terms—avoidance, acceptance, mitigation, and transfer—are strategies used in risk management.

From Andrew Ramdayal’s guide:

“Risk in security refers to the potential for loss, damage, or destruction of assets or data due to a threat exploiting a vulnerability. Risk management strategies include avoidance, acceptance, mitigation, and transfer.”

Once the theory has been tested and confirmed, the next step is to implement the solution based on the CompTIA troubleshooting model.

CompTIA Troubleshooting Model:

Identify the problem.

Establish a theory of probable cause.

Test the theory.

Establish a plan of action and implement the solution. ✅ (Correct step)

Verify full system functionality.

Document findings, actions, and outcomes.

Breakdown of Options:

A. Develop a theory – The theory has already been developed and tested.

B. Establish a plan of action – This happens before implementation, but since the issue is confirmed, it's time to act.

C. Implement the solution – Correct answer. The problem is confirmed, so the fix should be applied.

D. Document the findings – Documentation is the final step, not the next one.

Using a /30 subnet mask is the most efficient way to conserve IP space for a point-to-point connection between two routers. A /30 subnet provides four IP addresses, two of which can be assigned to the router interfaces, one for the network address, and one for the broadcast address. This makes it ideal for point-to-point links where only two usable IP addresses are needed.References: CompTIA Network+ study materials and subnetting principles.

The customer can access local resources (a database server), which means local networking is working. However, the inability to reach the internet suggests an issue with the default gateway. If the default gateway is unreachable, packets will not be routed outside the local network.

Breakdown of Options:

A. Incorrect DNS – DNS issues would cause problems resolving domain names, but the user should still be able to access external resources via IP addresses.

B. Unreachable gateway – ✅ Correct answer. If the default gateway is incorrect or unreachable, the device cannot route traffic to the internet.

C. Failed root bridge – STP (Spanning Tree Protocol) failures cause switching issues, but the user can still access local devices, meaning STP is not the problem.

D. Poor upstream routing – Would affect the entire network, not just one user.