Pass the CompTIA CompTIA Network+ N10-009 Questions and answers with CertsForce

A signal power of -97dB indicates a very weak signal, which can cause connectivity issues and slow speeds. Splitters on a coaxial line can degrade the signal quality further, so removing them can help improve the signal strength and overall connection quality.

Signal Quality: Splitters can reduce the signal strength by dividing the signal among multiple lines, which can be detrimental when the signal is already weak.

Direct Connection: Ensuring a direct connection from the modem to the incoming line can maximize signal quality and reduce potential points of failure.

Network References:

CompTIA Network+ N10-007 Official Certification Guide: Discusses troubleshooting connectivity issues and the impact of signal strength on network performance.

Cisco Networking Academy: Provides insights on maintaining optimal signal quality in network setups.

Network+ Certification All-in-One Exam Guide: Covers common network issues, including those related to signal degradation and ways to mitigate them.

EIGRP (Enhanced Interior Gateway Routing Protocol) is a Cisco proprietary advanced distance-vector routing protocol. While it operates within an Autonomous System (AS), it requires the AS number to be configured for routers to recognize each other as EIGRP neighbors.

OSPF (Open Shortest Path First) uses areas and routers must be in the same area to form adjacencies, but it doesn't require AS numbers in the same way.

FHRP (First Hop Redundancy Protocol) is not a routing protocol but a group of protocols (e.g., HSRP, VRRP) to ensure high availability at the default gateway level.

RIP (Routing Information Protocol) does not use autonomous system numbers.

???? Reference:

CompTIA Network+ N10-009 Official Objectives: 3.1 – Compare and contrast various routing technologies.

===========

Border Gateway Protocol (BGP): BGP is the most commonly used routing protocol for interconnecting WANs, especially across the internet. It is used for exchanging routing information between autonomous systems (AS), making it the backbone protocol for large-scale WANs.

IGP (A): Interior Gateway Protocols like OSPF and EIGRP are typically used within a single AS, not between them.

EIGRP (B): While it is efficient, EIGRP is primarily used for intra-domain routing and not ideal for WAN interconnection.

OSPF (D): While OSPF can be used for WANs, it is not as common as BGP for inter-AS communication.

Introduction to Subinterfaces:

Subinterfaces are logical interfaces created on a single physical interface. They are used to enable a router to support multiple networks on a single physical interface.

Use Case for Subinterfaces:

Subinterfaces are commonly used in scenarios where VLANs are implemented. A router with a single physical LAN port can be configured with multiple subinterfaces, each associated with a different VLAN.

This setup allows the router to route traffic between different VLANs.

Example Configuration:

Consider a router with a single physical interface GigabitEthernet0/0 and two VLANs, 10 and 20.

interface GigabitEthernet0/0.10

encapsulation dot1Q 10

ip address 192.168.10.1 255.255.255.0

!

interface GigabitEthernet0/0.20

encapsulation dot1Q 20

ip address 192.168.20.1 255.255.255.0

The encapsulation dot1Q command specifies the VLAN ID.

Explanation of the Options:

A. A router with only one available LAN port: This is correct. Subinterfaces allow a single physical interface to manage multiple networks, making it essential for routers with limited physical interfaces.

B. A firewall performing deep packet inspection: Firewalls can use subinterfaces, but it is not a requirement for deep packet inspection.

C. A hub utilizing jumbo frames: Hubs do not use subinterfaces as they operate at Layer 1 and do not manage IP addressing.

D. A switch using Spanning Tree Protocol: STP is a protocol for preventing loops in a network and does not require subinterfaces.

Conclusion:

Subinterfaces provide a practical solution for routing between multiple VLANs on a router with limited physical interfaces. They allow network administrators to optimize the use of available hardware resources efficiently.

To support VoIP on a network with limited switchports, the engineer should configure voice VLANs and enable 802.1Q tagging. Voice VLANs allow VoIP traffic to be prioritized and isolated from data traffic even when sharing the same physical port. 802.1Q is used for VLAN tagging, enabling multiple VLANs over a single physical link.

From Andrew Ramdayal’s guide:

“Voice VLANs allow IP phones and computers to share the same physical switch port while keeping their traffic separate. 802.1Q is used to tag VLAN traffic so that it can be appropriately routed and prioritized.”

VLANs (Virtual Local Area Networks) segment network traffic by department, allowing ACLs (Access Control Lists) to be applied based on VLAN membership, improving security and resource isolation.

Breakdown of Options:

A. VLAN – Correct answer. VLANs enable logical network segmentation, allowing ACLs per department.

B. DHCP – Assigns IP addresses but does not control access.

C. VPN – Provides remote access, not segmentation within a network.

D. STP – Prevents switching loops, not related to ACL implementation.

Content filtering can be used to block or restrict access to websites and services that facilitate torrenting and other prohibited activities. By implementing content filtering, the company can comply with the ISP's cease-and-desist order and prevent users from accessing torrent sites and engaging in prohibited activities.References: CompTIA Network+ study materials.

Definition of ESP (Encapsulating Security Payload):

ESP is a part of the IPsec protocol suite used to provide confidentiality, integrity, and authenticity of data. ESP encrypts the payload and optional ESP trailer, providing data confidentiality.

ESP Functionality:

ESP can encrypt the entire IP packet, ensuring that the data within the packet is secure from interception or eavesdropping. It also provides options for data integrity and authentication.

ESP operates in two modes: transport mode (encrypts only the payload of the IP packet) and tunnel mode (encrypts the entire IP packet).

Comparison with Other Protocols:

AH (Authentication Header): Provides data integrity and authentication but does not encrypt the payload.

GRE (Generic Routing Encapsulation): A tunneling protocol that does not provide encryption.

UDP (User Datagram Protocol) and TCP (Transmission Control Protocol): These are transport layer protocols that do not inherently provide encryption. Encryption must be provided by additional protocols like TLS/SSL.

Use Cases:

ESP is widely used in VPNs (Virtual Private Networks) to ensure secure communication over untrusted networks like the internet.

•API (Application Programming Interface) enables secure and granular access control, remote management, and logging, making it ideal for network monitoring.

•SNMP (A) is mainly used for device monitoring but lacks centralized logging and user-based privilege control.

•SIEM (C) is a security monitoring tool focused on log collection, not device management.

•SSO (D) is related to authentication, not monitoring.

????Reference: CompTIA Network+ N10-009 Official Documentation – Network Monitoring & Management Technologies.

•The issue described is a network bottleneck due to increased traffic after a merger.

•A collapsed core architecture consolidates the core and distribution layers into a single layer to improve efficiency and reduce latency.

•Until the 40GB switch is acquired, Link Aggregation (LAG) (IEEE 802.3ad / LACP) can be used to combine multiple physical links into a single logical link, increasing bandwidth and reducing bottlenecks.

•FHRP (First Hop Redundancy Protocol) (A) is used for gateway redundancy, not link aggregation.

•Route selection metric changes (B) help with routing decisions but don’t address physical link congestion.

•Load balancers (C) distribute traffic for applications, not network links.

????Reference: CompTIA Network+ N10-009 Official Documentation – Network Architecture and Performance Optimization.