Pass the CompTIA CompTIA Network+ N10-009 Questions and answers with CertsForce

The correct solution is to configure the connecting ports as trunk ports. When connecting switches, the uplink ports must be configured to carry traffic for multiple VLANs (trunking), not just a single access VLAN. Without trunking, VLAN tags may be dropped, and traffic from hosts will not reach the rest of the network or internet.

B. STP cables is a misnomer — STP refers to Spanning Tree Protocol or Shielded Twisted Pair cables, neither of which solves this logical configuration issue.

C. PoE budget is irrelevant because switches and hosts in this context don’t require PoE.

D. Link aggregation (LACP, EtherChannel) is for increasing bandwidth/redundancy across multiple links, not required with a single cable.

By enabling trunking on the uplink ports, the switches can pass VLAN-tagged traffic, ensuring hosts connected to the new switch have access to the same resources as those on the existing switch.

References (CompTIA Network+ N10-009):

Domain: Network Troubleshooting — VLAN trunking, inter-switch connectivity.

The most likely cause of buffering issues when moving outdoors is signal degradation. Wireless signals weaken as they travel through obstacles such as walls, glass, and air, leading to weaker connections and reduced data rates.

Breakdown of Options:

A. Network congestion – While congestion can slow down network speeds, it affects all users, not just those moving outdoors.

B. Wireless interference – Interference is possible but is more likely caused by other wireless signals rather than outdoor movement.

C. Signal degradation – Correct answer. Wireless signals weaken with distance and obstacles such as walls, reducing performance.

D. Client disassociation – Disassociation occurs when clients lose connection to the AP, but the question states that users experience buffering, indicating they are still connected but with a weak signal.

To validate routing between networks hosting Workstation A and File Server 2, follow these steps:

Review Routing Tables:

Check the routing tables of Router A, Router B, and Router C to identify any missing routes.

Identify Missing Routes:

Ensure that each router has routes to the networks on which Workstation A and File Server 2 are located.

Add Static Routes:

If a route is missing, add a static route to the relevant destination network via the correct interface.

Routing Table:

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

S* 0.0.0.0/0 is directly connected, GigabitEthernet3

10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks

C 10.0.4.0/22 is directly connected, GigabitEthernet2

C 10.0.6.0/24 is directly connected, GigabitEthernet2

L 10.0.6.1/32 is directly connected, GigabitEthernet2

172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 172.16.27.0/30 is directly connected, GigabitEthernet3

L 172.16.27.1/32 is directly connected, GigabitEthernet3

Routing Table:

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

S* 0.0.0.0/0 is directly connected, GigabitEthernet1

10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks

C 10.0.0.0/22 is directly connected, GigabitEthernet1

L 10.0.0.1/32 is directly connected, GigabitEthernet1

172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 172.16.27.4/30 is directly connected, GigabitEthernet1

L 172.16.27.5/32 is directly connected, GigabitEthernet1

Routing Table:

10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks

S 10.0.0.0/22 [1/0] via GigabitEthernet1

S 10.0.4.0/22 [1/0] via GigabitEthernet2

172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 172.16.27.0/30 is directly connected, GigabitEthernet2

L 172.16.27.2/32 is directly connected, GigabitEthernet2

C 172.16.27.4/30 is directly connected, GigabitEthernet1

L 172.16.27.6/32 is directly connected, GigabitEthernet1

Install Static Route to 10.0.0.0/22 via 172.16.27.1 (assuming Router C's IP is 172.16.27.1):

Destination Prefix: 10.0.0.0

Destination Prefix Mask: 255.255.252.0

Interface: GigabitEthernet3

Install Static Route to 10.0.4.0/22 via 172.16.27.5 (assuming Router C's IP is 172.16.27.5):

Destination Prefix: 10.0.4.0

Destination Prefix Mask: 255.255.252.0

Interface: GigabitEthernet1

Install Static Route to 10.0.6.0/24 via 172.16.27.2 (assuming Router A's IP is 172.16.27.2):

Destination Prefix: 10.0.6.0

Destination Prefix Mask: 255.255.255.0

Interface: GigabitEthernet2

Install Static Route to 10.0.0.0/22 via 172.16.27.1 (assuming Router B's IP is 172.16.27.1):

Destination Prefix: 10.0.0.0

Destination Prefix Mask: 255.255.252.0

Interface: GigabitEthernet1

Summary of Static Routes:

Router A:

ip route 10.0.0.0 255.255.252.0 GigabitEthernet3

Router B:

ip route 10.0.4.0 255.255.252.0 GigabitEthernet1

Router C:

ip route 10.0.6.0 255.255.255.0 GigabitEthernet2

ip route 10.0.0.0 255.255.252.0 GigabitEthernet1

These configurations ensure that each router knows the correct paths to reach Workstation A and File Server 2, resolving the connectivity issue.

Importance of Proper Termination:

Cat 8 cabling requires precise termination practices to ensure signal integrity and reduce interference. One common requirement is to wrap the end connections in copper tape to maintain shielding and reduce electromagnetic interference (EMI).

Interference Troubleshooting:

Interference in high-frequency cables like Cat 8 can be caused by improper shielding or grounding. Checking the end connections for proper wrapping in copper tape is a crucial step.

Why Other Options are Less Likely:

Passthrough modular crimping plugs: Not specifically related to interference issues and are typically used for ease of cable assembly.

Connecting RX/TX wires to different pins: Would likely result in no connection or incorrect data transmission rather than interference.

Running a speed test on a device that can only achieve 100Mbps speeds: This would not diagnose interference and would not provide relevant information for Cat 8 cabling rated for higher speeds.

Corrective Actions:

Verify that all end connections are properly wrapped with copper tape before termination.

Ensure that the shielding is continuous and properly grounded throughout the installation.

Retest the cabling for interference after making corrections.

Once the theory has been tested and confirmed, the next step is to implement the solution based on the CompTIA troubleshooting model.

CompTIA Troubleshooting Model:

Identify the problem.

Establish a theory of probable cause.

Test the theory.

Establish a plan of action and implement the solution. ✅ (Correct step)

Verify full system functionality.

Document findings, actions, and outcomes.

Breakdown of Options:

A. Develop a theory – The theory has already been developed and tested.

B. Establish a plan of action – This happens before implementation, but since the issue is confirmed, it's time to act.

C. Implement the solution – Correct answer. The problem is confirmed, so the fix should be applied.

D. Document the findings – Documentation is the final step, not the next one.

Changing the default password is a fundamental step in device hardening, as default credentials are widely known and published online, posing a significant security risk if not updated. The document notes:

“Default passwords are often known by attackers and published on the internet. Changing them to unique, strong passwords is a critical first step in securing network devices against unauthorized access.”

Definition of GDPR:

General Data Protection Regulation (GDPR) is a regulation in EU law on data protection and privacy for all individuals within the European Union and the European Economic Area. It also addresses the transfer of personal data outside the EU and EEA areas.

Scope and Objectives:

GDPR aims to give individuals control over their personal data and to simplify the regulatory environment for international business by unifying the regulation within the EU.

It enforces rules about data protection, requiring companies to protect the personal data and privacy of EU citizens for transactions that occur within EU member states.

Comparison with Other Options:

SCADA (Supervisory Control and Data Acquisition): Refers to control systems used in industrial and infrastructure processes, not related to personal data protection.

SAML (Security Assertion Markup Language): A standard for exchanging authentication and authorization data between parties, not specifically for personal data protection.

PCI DSS (Payment Card Industry Data Security Standard): A set of security standards designed to ensure that all companies that accept, process, store or transmit credit card information maintain a secure environment, not specific to personal data protection in Europe.

Key Provisions:

GDPR includes provisions for data processing, data subject rights, obligations of data controllers and processors, and penalties for non-compliance.

In a mesh topology, every node is directly connected to every other node. This provides high redundancy and reliability, as there are multiple paths for data to travel between nodes. This topology is often used in networks where high availability is crucial.References: CompTIA Network+ study materials.

A misaligned parabolic antenna can cause a significant increase in input errors because the signal is not properly focused or directed towards the receiving antenna, resulting in poor reception and data corruption. The document confirms:

“Misalignment of parabolic microwave antennas can lead to weak or incorrect signal reception, causing an increase in input errors and connectivity issues on the link.”

Increasing the MTU (Maximum Transmission Unit) size allows larger frames to be transmitted, reducing overhead and improving throughput — especially for large file transfers like backups.

A. QoS prioritizes traffic but doesn’t reduce backup times directly.

B. SDN is a network management model, not a parameter change.

D. VXLAN encapsulates VLANs, not relevant to backup speeds.

E. TTL is for packet lifetime, not throughput.

References (CompTIA Network+ N10-009):

Domain: Network Infrastructure — MTU, jumbo frames, performance tuning.