Pass the CompTIA CompTIA Network+ N10-009 Questions and answers with CertsForce

An access point (AP) provides users with an extended footprint that allows connections from multiple devices within a designated Wireless Local Area Network (WLAN).

Router: Typically used to connect different networks, not specifically for extending wireless coverage.

Switch: Used to connect devices within a wired network, not for providing wireless access.

Access Point (AP): Extends wireless network coverage, allowing multiple wireless devices to connect to the network.

Firewall: Primarily used for network security, controlling incoming and outgoing traffic based on security rules, not for providing wireless connectivity.

Network References:

CompTIA Network+ N10-007 Official Certification Guide: Explains the roles and functions of network appliances, including access points.

Cisco Networking Academy: Provides training on deploying and managing wireless networks with access points.

Network+ Certification All-in-One Exam Guide: Covers network devices and their roles in creating and managing networks.

Link aggregation (also known as port trunking or EtherChannel) combines multiple network connections in parallel to increase throughput and provide redundancy. When two switches are connected with multiple links without any additional configuration, a Layer 2 loop may occur. Link aggregation prevents these loops by treating the multiple connections as a single logical link, using a protocol such as LACP (Link Aggregation Control Protocol).

From Andrew Ramdayal’s guide:

“Link aggregation allows you to combine multiple network connections to increase the bandwidth and provide redundancy. It helps prevent Layer 2 loops when connecting switches with multiple links by making them operate as a single logical interface.”

Link Layer Discovery Protocol (LLDP) is a network protocol used for discovering devices and their capabilities on a local area network, primarily at the data link layer (Layer 2). It helps in identifying the connected switch and the specific port to which a device is connected. When troubleshooting a VoIP handset connection, the technician can use LLDP to determine the exact switch and port where the handset is connected. This protocol is widely used in network management to facilitate the discovery of network topology and simplify troubleshooting.

Other options such as IKE (Internet Key Exchange), VLAN (Virtual LAN), and netstat (network statistics) are not suitable for identifying the switch and port information. IKE is used in setting up secure IPsec connections, VLAN is used for segmenting networks, and netstat provides information about active connections and listening ports on a host but not for discovering switch port details.

SIEM (Security Information and Event Management) systems are used to aggregate and analyze log data from various sources, including firewalls, to detect potential security incidents and assist in regulatory compliance. The document explains:

“SIEM solutions aggregate and analyze log and event data from multiple devices, including firewalls, across different locations. They help in real-time monitoring, incident response, and ensuring compliance with security policies.”

Microwaves are known to interfere with the 2.4GHz frequency, which is the same frequency used by many wireless networks. This can cause signal degradation and intermittent connectivity issues, especially if the WAP is placed near such devices.

=================

Wi-Fi 6E is the best choice for high-density environments, such as a university campus. It:

Supports more devices with OFDMA (Orthogonal Frequency-Division Multiple Access)

Uses the 6GHz band, reducing congestion

Provides faster speeds and lower latency

This makes Wi-Fi 6E ideal for large networks with high-bandwidth demands, like those in a university setting.

Breakdown of Options:

A. Bluetooth – Used for short-range, low-power connections, not large-scale wireless networks.

B. Wi-Fi 6E – ✅ Correct answer. Designed for high-density environments, improving speed and efficiency.

C. 5G – Used for mobile networks, but not ideal for campus-wide local wireless infrastructure.

D. LTE – Used for cellular data, not for campus-wide Wi-Fi.

Asymmetrical routing occurs when packets take different paths to and from the destination, leading to instability in network communication. The use of two different MPLS providers with OSPF can lead to this type of routing issue, especially if the paths aren't carefully configured and managed. This can cause unexpected routing behaviors and instability in a dual-WAN setup. (Reference: CompTIA Network+ Study Guide, Chapter on Network Routing)

Multi-factor authentication (MFA) requires two or more different categories of authentication factors:

Something you know (password, PIN)

Something you have (smart card, hardware token)

Something you are (biometric)

The only valid second factor here is a hard token (e.g., a key fob generating one-time codes).

A. PIN is still “something you know,” the same category as a password.

B. Favorite color is a weak knowledge-based factor, not a true second factor.

D. Mother’s maiden name is also “something you know” and insecure.

References (CompTIA Network+ N10-009):

Domain: Network Security — Authentication methods, MFA factor categories.

A Security Information and Event Management (SIEM) system collects, correlates, and analyzes logs from multiple sources in real-time, providing enhanced visibility across multivendor environments.

Breakdown of Options:

A. SNMP – SNMP is used for network device monitoring, but it lacks real-time correlation across multiple vendors.

B. SIEM – Correct answer. SIEM aggregates, analyzes, and correlates logs from multiple sources, providing real-time visibility.

C. Nmap – Nmap is a network scanning tool used for mapping hosts and detecting open ports but does not provide log correlation.

D. Syslog – Syslog collects logs but does not correlate or analyze them in real-time.

When a new VLAN is created, it typically exists on a different subnet. If DHCP servers are on a different VLAN, the network needs an IP helper address to forward DHCP requests correctly. Without it, clients in the new VLAN won’t receive an IP address.

Breakdown of Options:

A. Scope size – Increasing the DHCP scope would not resolve the issue if requests aren't reaching the server.

B. Address reservations – Reservations only assign specific addresses to devices; they do not fix DHCP communication issues.

C. Lease time – Changing the lease time does not impact DHCP functionality across VLANs.

D. IP helper – Correct answer. This forwards DHCP requests across VLANs to the DHCP server.