Winter Sale Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: pass65

Pass the Cisco CCNP Collaboration 350-801 Questions and answers with CertsForce

Viewing page 7 out of 13 pages
Viewing questions 61-70 out of questions
Questions # 61:

Question # 61

Refer to the exhibit. An administrator must replace the T1 card with an E1 card. What is the correct configuration if the administrator was asked to configure 12 time slots?

Options:

A.

350-801 Question 61 Option 1


B.

61


C.

61


D.

61


Expert Solution
Questions # 62:

What is the purpose of a hybrid Local Gateway?

Options:

A.

to handle calls between Webex Calling and Cisco Calling Plans


B.

to handle calls between Webex Calling and Cloud Connected PSTN


C.

to handle calls between Cisco IJCM and Webex Calling


D.

to handle calls between the Public Switched Telephone Network and Webex Calling


Expert Solution
Questions # 63:

A Company s employees have been complaining that they have been unable to select options on the internal IVR of the help desk. IT support has been given Cisco UCM traces and below is the snippet of the SDP of the INVITE packet.

Question # 63

How is this issue resolved?

Options:

A.

Configure CODEC for G.729.


B.

Configure DTMF for KPML.


C.

Configure CODEC for G.722.


D.

Configure DTMF for RFC 2833.


Expert Solution
Questions # 64:

Regarding SIP integrations with Cisco Unified Communications Manager, if the Cisco Unity Connection is configured to listen for incoming IPv4 and IPv6 traffic, how should the addressing mode be set up in the Cisco Unity Connection?

Options:

A.

Set up is not required.


B.

Set up for each group to use IPv4 and IPv6.


C.

Set up media ports for each port group to use IPv4.


D.

Set up IPv4 and IPv6 in Cisco Unified CM.


Expert Solution
Questions # 65:

Cisco UCM delays routing of a call during digit analysis with an overlapping dial plan. How long is the default wait time?

Options:

A.

5 seconds


B.

10 seconds


C.

15 seconds


D.

20 seconds


Expert Solution
Questions # 66:

Which two technical reasons make QoS a necessity in a video deployment? (Choose Two)

Options:

A.

Low response time between endpoints


B.

Provisioned bandwidth of the link


C.

Variable bit rate of the video stream


D.

Bursly behavior of video traffic


Expert Solution
Questions # 67:

Which Cisco UCM service parameter is enabled to disconnect a multiparty call when the call initiator hangs up?

Options:

A.

H.225 Block Setup Destination


B.

Drop Ad Hoc Conference


C.

Enterprise Feature Access Code for Conference


D.

Block OffNet To OffNet Transfer


Expert Solution
Questions # 68:

An engineer must deploy the Cisco Webex app to a Virtual Desktop Infrastructure (VDI) environment and support full-featured meetings. Which action must the engineer take to meet these requirements?

Options:

A.

Configure the VDI thin client and install the Webex app


B.

From Control Hub. configure VDI optimization for the Webex app


C.

Install three separate VDI plugins on the VDI thin client


D.

Install two separate VDI plugins on the VDI thin client


Expert Solution
Questions # 69:

An engineer is configuring a Cisco Unified Border Element to allow the video endpoints to negotiate without the Cisco Unified Border Element interfering in the process. What should the engineer configure on the Cisco Unified Border Element to support this process?

Options:

A.

Configure path-thru content sdp on the voice service.


B.

Configure a hardcoded codec on the dial peers.


C.

Configure a transcoder for video protocols.


D.

Configure codec transparent on the dial peers.


Expert Solution
Questions # 70:

After an engineer runs the utils ntp status command on the Cisco Unified Communications Manager publisher, the stratum value is 16. Which issue can the

Cisco Unified CM cluster experience?

Options:

A.

Unified CM sends an NTPv4 packet.


B.

Database replication is not synchronized on the Unified CM nodes.


C.

The cluster loses access to port 124 at the firewall.


D.

The date/time group on all phones defaults to the time zone of the engineer.


Expert Solution
Viewing page 7 out of 13 pages
Viewing questions 61-70 out of questions