Pass the NFPA Fire Protection Specialist CFPS Questions and answers with CertsForce

An as built plan review is a type of plan review that may provide information about a modification such as the removal of an abandoned underground flammable liquid tank. An as built plan review is conducted after the construction or alteration of a building or system is completed and before the final approval or acceptance by the AHJ. An as built plan review verifies that the building or system conforms to the approved plans and specifications and complies with the applicable codes and standards. An as built plan review may also identify any changes or deviations from the original plans that occurred during the construction or alteration process, such as the removal of an underground tank.References:

NFPA 1: Fire Code, 2018 Edition, Section 1.12.8.1.11

Fire Protection Handbook, 20th Edition, Volume 1, Chapter 5, Section 5.2.3.42

The minimum width of a doorway in a means of egress to accommodate a person in a wheelchair is 32 inches (813 mm).This is based on the requirements of the Americans with Disabilities Act (ADA) and the International Building Code (IBC), which both specify that doors in a path of egress and doors on an accessible route must have a clear opening width of at least 32 inches (813 mm)12. This width allows enough space for a person in a wheelchair to maneuver through the doorway without difficulty. A wider doorway may be preferable for some types of wheelchairs or other assistive devices, but 32 inches (813 mm) is the minimum standard for accessibility and safety.References:DECODED: Calculating the Egress Width of Door Openings - I Dig Hardware;Digital Codes.

The coefficient of discharge of a fire hydrant when the outlet is smooth and well-rounded is 0.90. This is the highest coefficient given by NFPA 291 for fire hydrant outlets, and it means that the stream is almost as large as the outlet diameter. The coefficient of discharge is a factor that accounts for the difference between the actual flow and the theoretical flow from an orifice, based on the shape and condition of the outlet1. A lower coefficient means that the stream is more restricted and has a smaller cross-sectional area than the outlet. NFPA 291 provides three coefficients for fire hydrant outlets, depending on how the outlet projects into the barrel: 0.90 for smooth and well-rounded outlets, 0.80 for outlets with a hexagonal or square projection, and 0.70 for outlets with a long projection or adamaged edge2. The coefficient of discharge is used to calculate the flow rate from the pitot pressure measured at the centerline of the stream3. References:

Fire Fighting Foams - Chemguard

Guide to Hydrant Flow Testing | WSRB

New Fire Hydrant Flow Test Charts (PDF) - MeyerFire

The minimum pipe diameter size for direct discharge of steam inside a water tank is 2 in. (50 mm), according to NFPA 13, Standard for the Installation of Sprinkler Systems. This is to prevent water hammer, noise, and vibration caused by the rapid condensation of steam when it contacts the water. The pipe should also be equipped with a check valve to prevent backflow of water into the steam source.References: NFPA 13, Standard for the Installation of Sprinkler Systems, 2023 Edition, Chapter 8, Section 8.16.4.5.3; NFPA Fire Protection Handbook, 21st Edition, Chapter 14, Section 14.3.4.2.

Fire extinguisher

Explore

smothering.

The primary mechanism by which carbon dioxide extinguishes fire is smothering, or displacing the oxygen that the fire needs to sustain combustion. Carbon dioxide is a gas that is heavier than air, so when it is released from the extinguisher, it forms a blanket over the fire and pushes away the oxygen.Without oxygen, the fire cannot continue to burn and is extinguished1234

Cooling is a secondary mechanism by which carbon dioxide extinguishes fire. Carbon dioxide is stored as a liquid under high pressure in the extinguisher, and when it is released, it expands rapidly and cools down. The cold gas absorbs heat from the fire and lowers the temperature of the fuel below its ignition point.However, cooling is not the main effect of carbon dioxide, as it is less effective than water in reducing the heat of the fire1234

Saponification and chemical inhibition are not mechanisms by which carbon dioxide extinguishes fire. Saponification is a process by which wet chemical agents react with fats and oils to form a soapy foam that seals the surface of the fire and prevents re-ignition. Chemical inhibition is a process by which dry chemical agents interfere with the chemical chain reaction of the fire and stop the production of free radicals that propagate the combustion.These mechanisms are used by other types of fire extinguishers, such as Class K and Class D extinguishers, respectively1234

References:

Carbon Dioxide Extinguishers - University of South Carolina4

How Does A Co2 Fire Extinguisher Work2

Why is Carbon Dioxide Used to Extinguish Oil Fires3

What is a Carbon Dioxide Fire Extinguisher?- Safeopedia1

Aqueous film-forming agents (AFFF) are synthetic foam concentrates that can be proportioned into final concentrations of 1%, 3%, and 6%, depending on the type of fuel and application method12. AFFF forms a thin aqueous film on the surface of the flammable liquid, which prevents vapor release and provides rapid fire knockdown and extinguishment3. AFFF is suitable for Class B fires involving hydrocarbon fuels such as gasoline, diesel, kerosene, etc. References:

Fire Fighting Foams - Chemguard

Extinguishing foam: types, operation and application areas

[NFPA 11: Standard for Low-, Medium-, and High-Expansion Foam]

79% of fire departments surveyed participate in the delivery of emergency medical services (EMS).This is based on the NFPA report “US Fire Department Profile 2020”1, which states that nationwide, 37% of fire departments provided no EMS, 46% provided basic life support (BLS), and 17% provided advanced life support (ALS). Therefore, the percentage of fire departments that provided either BLS or ALS is 46% + 17% = 63%. However, this does not include fire departments that provided EMS through a third-party contract or agreement.According to the NFPA fire service survey from 2018–20202, 16% of fire departments reported having such an arrangement. Therefore, the percentage of fire departments that participated in the delivery of EMS in some form is 63% + 16% = 79%.References:

NFPA report - U.S.fire department profile3

US Fire Department Profile 2020 Supporting Tables2

A rate-of-rise heat detector is a type of heat detector that automatically resets after operation, when the ambient temperature drops below the operating temperature. This is because a rate-of-rise heat detector operates on a rapid rise in element temperature of 6.7° to 8.3°C (12° to 15°F) increase per minute, irrespective of the starting temperature1 If the temperature rise stops or reverses, the detector will reset itself and stop sending an alarm signal to the control panel2 A rate-of-rise heat detector can also have a fixed temperature element that will trigger an alarm at a specified temperature, but this element is not self-resetting and requires replacement after activation2

References:

Heat Detectors Selection Guide: Types, Features, Applications - GlobalSpec2

Heat detector - Wikipedia1

Fire alarm visible appliance source intensity is measured in candela, which is the unit of luminous intensity in a given direction. Candela is defined as the amount of light emitted by a single candle in a specific direction. The intensity of a strobe light depends on the candela rating, the flash rate, and the flash duration. The higher the candela rating, the brighter the light. The National Fire Protection Association (NFPA) and the Americans with Disabilities Act (ADA) have established minimum and maximum candela ratings for fire alarm visible appliances in different locations and applications.References:Strobe Light Requirements: Proper location of visible notification …;Handbook of Visual Notification Appliances for Fire Alarm Applications;Audible Visible Appliance Reference Guide - Fire - studylib.net