Pass the EMC Proven Professional D-UN-DY-23 Questions and answers with CertsForce

The Unity 380/380F system supports two types of I/O modules: 12 Gb/s SAS back-end and 10 GbE Base-T front-end. The 12 Gb/s SAS back-end module provides connectivity to the disk drives and expansion enclosures, while the 10 GbE Base-T front-end module provides network connectivity to the hosts and clients. The Unity 380/380F system has four I/O module slots, two for each SP. The 12 Gb/s SAS back-end module must be installed in slot 0 of each SP, and the 10 GbE Base-T front-end module can be installed in slot 1 of each SP. Therefore, the correct answer is C. 12 Gb/s SAS 10 GbE Base-T. References:

Dell EMC Unity: Hardware Information Guide

Dell EMC Unity: Installation Guide

Data Reduction is a feature that reduces the amount of physical storage space required to store user data on a LUN. Data Reduction is enabled at the LUN level and applies to all the data in the LUN, including snapshots and thin clones. Data Reduction consists of two components: compression and deduplication. Compression reduces the size of data blocks by removing redundant information, while deduplication eliminates duplicate blocks across the LUN. When Data Reduction is enabled on a LUN, all writes to the LUN will go through the Data Reduction logic before being written to the storage pool. If the LUN is part of a consistency group, Data Reduction will be enabled on all the LUNs in the consistency group, and all writes to any LUN in the group will go through the Data Reduction logic. This ensures that the data in the consistency group is consistent and protected by the same Data Reduction settings. References:

Dell EMC Unity: Data Reduction Overview

Dell EMC Unity: Data Reduction Configuration and Best Practices

If the time difference between the current system (UTC) time and the NTP server time is too large (approximately 17 minutes), the user cannot configure an NTP server during initial configuration. The user will need to adjust the time while in “Set time manually” mode before changing to “Enable NTP synchronization”. This is to avoid potential issues with data replication, snapshots, and audit logs that rely on accurate time stamps. References: Dell EMC Unity: How to change System Time from ‘Set time manually’ option to NTP2, page 1.

The preferred FC Port for synchronous replication for a Dell Unity XT 380 system is Fibre Channel Port 4 of SPA and SPB. This port is dedicated for synchronous replication traffic and has the highest priority and bandwidth allocation. Synchronous replication is a method of replicating data between two Dell Unity systems with zero recovery point objective (RPO). It requires a low-latency and high-bandwidth network connection between the source and destination systems.

 Mixing FC and iSCSI protocols for the same host and array is not supported by Dell EMC Unity. This can cause issues with multipathing, failover, and performance. The best practice is to use one protocol per host and array pair. If the host needs to access both FC and iSCSI LUNs from different arrays, then separate vSwitches and port groups should be used for each protocol. References: Dell EMC Unity: Best Practices Guide1, page 19.

The total cache availability for caching the flash drives on a Dell Unity XT 480 system with one pool of flash drives, 192 GB of RAM, and 1.2 TB of FAST Cache is 3.58 TB. This is calculated by adding the system memory (RAM), the FAST Cache, and the pool cache. The system memory is 192 GB, which is equivalent to 0.18 TB. The FAST Cache is 1.2 TB, which is a dedicated cache for the flash drives. The pool cache is 2.2 TB, which is a portion of the flash drives that is reserved for caching the pool data. Therefore, the total cache availability is 0.18 + 1.2 + 2.2 = 3.58 TB.

A characteristic of Host Groups is that block storage resources added to a host group are accessible to all the member hosts. A Host Group is a logical grouping of hosts that share the same access permissions and settings for block storage resources. By adding block storage resources to a host group, the user can simplify the management and allocation of storage for multiple hosts. Access to block storage resources does not need to be set before adding hosts to a host group, as the access permissions can be modified later. Hosts added to a host group can have mapped block storage resources, as long as they are not in conflict with the host group resources. Block storage resources attached to one of the member hosts are not accessible to the entire host group, unless they are also added to the host group.

When Advanced Deduplication is disabled on a LUN, the existing data that was deduplicated remains in its reduced state, and only new data written to the LUN is not deduplicated. To remove the Advanced Deduplication savings from the LUN, the administrator must perform a Local LUN Move operation, which copies the data from the source LUN to a destination LUN without deduplication. The destination LUN must have Advanced Deduplication disabled, and must be in the same storage pool as the source LUN. After the Local LUN Move is completed, the source LUN can be deleted and the destination LUN can be renamed as the original LUN. References: Dell Unity: Data Reduction2, page 9.

VMware datastore is a logical container that holds virtual machine files and other data. There are three types of VMware datastore that can be defined by using UI or CLI interfaces from the Dell Unity XT platform:

vVol (Block): A vVol datastore is a block-based storage object that is formatted with the VMware Virtual Volumes (vVol) framework and used to store virtual machine files and metadata. A vVol datastore can be created by using the Unisphere UI or the UEMCLI interface on the Dell Unity XT system. A vVol datastore can provide granular control, policy-based management, and improved performance for virtual machines.

NFS (File): An NFS datastore is a file-based storage object that is formatted with the Network File System (NFS) protocol and used to store virtual machine files and other data. An NFS datastore can be created by using the Unisphere UI or the UEMCLI interface on the Dell Unity XT system. An NFS datastore can provide scalability, flexibility, and efficiency for virtual machines.

VMFS (Block): A VMFS datastore is a block-based storage object that is formatted with the VMware File System (VMFS) and used to store virtual machine files and other data. A VMFS datastore can be created by using the Unisphere UI or the UEMCLI interface on the Dell Unity XT system. A VMFS datastore can provide high performance, reliability, and compatibility for virtual machines.

The snapshot option that is set automatically when a pool is configured is the Pool Automatic Deletion Policy. This option determines how the system handles the deletion of snapshots when the pool reaches a certain threshold of capacity utilization. The user can choose between three policies: Never Delete, Delete Oldest, or Delete Lowest Priority. The Total Pool Consumption and the Snapshot Pool Consumption are not snapshot options, but rather metrics that show the amount of pool space consumed by the pool data and the snapshots respectively.