Black Friday Reward - Upto 75% off - Ends in 0d 00h 00m 00s - Coupon code: CFsave75

Pass the Cisco CCNP Wireless 300-120 Questions and answers with CertsForce

Viewing page 2 out of 4 pages
Viewing questions 11-20 out of questions
Questions # 11:

What is the difference between PIM sparse mode and PIM dense mode?

Options:

A.

Sparse mode supports only one switch. Dense mode supports multiswitch networks.


B.

Sparse mode floods. Dense mode uses distribution trees.


C.

Sparse mode uses distribution trees. Dense mode floods.


D.

Sparse mode supports multiswitch networks. Dense mode supports only one switch.


Expert Solution
Questions # 12:

An engineer wants to upgrade the APs in a Cisco FlexConnect group. To accomplish this upgrade, the FlexConnect AP Upgrade setting will be used. One AP of each model with the lowest MAC address in the group must receive the upgrade directly from the controller. Which action accomplishes this direct upgrade?

Options:

A.

Remove the APs from the group.


B.

Reboot all APs before the upgrade.


C.

Allocate the master APs to different groups.


D.

Do not set any master APs.


Expert Solution
Questions # 13:

A network administrator of a school district must implement a DNS-based ACL to block students from accessing certain teacher URLs where test papers are hosted. The infrastructure contains a Cisco Catalyst 9800 WLC with 25 9136 APs. The administrator configured the URL Filter List called urllist_flex_pre, applied the URL Filter List to the default Flex Profile, and defined Preauth called urllist_local_preauth and Postauth called urllist_local_postaut URL Filter List. Which configuration must the administrator apply to implement the ACL on the default policy profile?

Question # 13

Question # 13

Options:

A.

Option A


B.

Option B


C.

Option C


D.

Option D


Expert Solution
Questions # 14:

A wireless engineer deployed all remote sites as FlexConnect. The client VLAN assignment on these sites is configured manually mapped by WLAN and using local switching. Dynamic VLAN assignment is provided by the newly deployed Cisco ISE. Which IETF attribute must be configured on the AAA server to send that VLAN ID?

Options:

A.

Tunnel-Medium-Type


B.

Tunnel-Client-Endpoint


C.

Tunnel-Assignment-ID


D.

Tunnel-Private-Group-ID


Expert Solution
Questions # 15:

An engineer is implementing profiling for BYOD devices using Cisco ISE. When using a distributed model, which persona must the engineer configure with the profiling service?

Options:

A.

Device Admin Node


B.

Primary Admin Node


C.

Monitor Node


D.

Policy Services Node


Expert Solution
Questions # 16:

Which command set configures a Cisco Catalyst 9800 Series Wireless Controller so that the client traffic enters the network at the AP switch port?

Question # 16

Options:

A.

Option A


B.

Option B


C.

Option C


D.

Option D


Expert Solution
Questions # 17:

An engineer must implement a CPU ACL that blocks web management traffic to the controller, but they also must allow guests to reach a Web Authentication Redirect page. To which IP address is guest client HTTPS traffic allowed for this to work?

Options:

A.

DNS server IP


B.

controller management IP


C.

virtual interface IP


D.

client interface IP


Expert Solution
Questions # 18:

Refer to the exhibit.

What is the reason that the wireless client cannot get the RUN state?

Question # 18

Options:

A.

It has no communication with Cisco ISE.


B.

An authentication error has occurred.


C.

It is not getting the IP address.


D.

Because of central switching, the AP must reach the Cisco ISE directly.


Expert Solution
Questions # 19:

An engineer must implement intrusion protection on the WLAN. The AP coverage is adequate and on-channel attacks are the primary concern. The building is historic, which makes adding APs difficult. Which AP mode and submode must be implemented?

Options:

A.

AP mode: local, AP submode: none


B.

AP mode: monitor, AP submode: WIPS


C.

AP mode: monitor, AP submode: none


D.

AP mode: local, AP submode: WIPS


Expert Solution
Questions # 20:

What must be configured on the Global Configuration page of the WLC for an AP to use 802.1x to authenticate to the wired infrastructure?

Options:

A.

local access point credentials


B.

RADIUS shared secret


C.

TACACS server IP address


D.

supplicant credentials


Expert Solution
Viewing page 2 out of 4 pages
Viewing questions 11-20 out of questions