Pass the Nokia SRC Certification 4A0-100 Questions and answers with CertsForce

In the diagram:

R2 and R4 areboth within AS 65540, which indicates that they are in thesame Autonomous System.

eBGP (External Border Gateway Protocol)is designed for routingbetween different ASes(inter-AS routing).

Since R2 and R4 are in thesame AS, you would use:

OSPForIS-IS(both interior gateway protocols – IGPs)✔

Static routingis also valid between any two routers if manually configured✔

eBGP❌is invalid between routersin the same AS.

➡The correct protocol in that case would beiBGP (internal BGP)if BGP were to be used within the AS.

Therefore, the correct answer is: D. eBGP

A/26 subnetmeans26 bits for the networkand6 bits for host addressing(32 - 26 = 6):

2⁶ = 64 total addresses per subnet

64 - 2 =62 usable host addresses per subnet

/24 to /26 increases subnet bits by 2, so:

2² =4 subnetsfrom one /24

But the question asks aboutusing /26, which means:

From /24 → each /26 block gives64 IPs

So you get4 subnets total

But the options must be interpreted carefully!

→Let's calculate again properly:

/26 = 64 addresses per subnet (2⁶)

Usable hosts per subnet = 64 - 2 = 62

Number of subnets in /24 when divided by /26 = 2^(26 - 24) = 4 subnets

So correct result is:

4 subnets, 62 hosts per subnet→Correct Answer: C

However,Option D says 8 subnets, 30 hosts per subnet, which actually matches a/27 mask, not /26.

Final Correct Answer:C

TheIngress Label Edge Router (LER)is the first router that:

Receives an unlabeled IP packet.

Applies an MPLS labelbased on its forwarding decision.

Forwards it into theMPLS core.

Option A is correct– Ingress LER does MPLS label push.

Option B (Egress LER)– removes labels at the end of the path.

Option C (LSR)– switches labels, but doesn’t push them onto unlabeled packets.

Option D– is not a specific MPLS role.

Ahubis aphysical layer (Layer 1)networking device used to connect multiple Ethernet devices in a network. Unlike switches or routers, hubs donot inspect or process frame headers. Instead, they perform a simple task:

Receive a signal (electrical or optical) on one port

Replicate that signal identically to all other ports

This means the hubdoes not examine Layer 2 (MAC addresses) or Layer 3 (IP addresses)and doesnot perform intelligent forwarding. It merelybroadcasts all incoming traffic to every other connected device, often resulting inhigh collision domainsand poor efficiency.

Option Adescribes arepeater, not a hub.

Option Cdescribes aswitch(Layer 2 device).

Option Ddescribes arouter(Layer 3 device).

Option Bis correct: A hub does not inspect headers and replicates traffic blindly.

TheShortest Path Tree (SPT)is calculated byLink-State routing protocolslikeOSPFandIS-ISusing:

Acomplete map of the network topology.

Each router uses algorithms likeDijkstra’sto compute the shortest paths to all destinations.

Option C is correct– fullnetwork topologyis used.

Option Arefers to Distance Vector methods.

Option BandDare results of topology analysis but not the input used.

TheDHCP client/server exchangefollows a specific four-step sequence known asDORA:

Discover– Client broadcasts to find available DHCP servers.

Offer– DHCP server responds with an IP address offer.

Request– Client requests the offered IP.

Acknowledgement– Server confirms the lease.

This ensuresdynamic IP configurationand is used in enterprise and home networks.

On theNokia 7750 SR, theControl Processor Module (CPM)includes two compact flash slots,CF1 and CF2, which are used for storing crucial system files. These include:

Runtime software image

Configuration files

Logs and backup configurations

BothCF1 and CF2are used for redundancy and flexibility. Typically, CF1 is designated as the primary storage location for the active software image and configuration, while CF2 serves as a backup. In some configurations, the router can boot from either CF1 or CF2 depending on system settings and availability.

This redundancy is essential for high availability and fast recovery in the event of a failure or manual software update.

Comprehensive and Detailed Explanation From Exact Extract:

In theNokia SR OS CLI, specifically in bothclassic CLIandMD-CLI, the"?" keyis used to display a list of all possible command options at a given point in the CLI, along with a brief description of each option.

This functionality helps the user in command discovery and reduces the chances of syntactical errors by showing only valid options.

The"Tab"key, while helpful, is primarily used forauto-completionand not for displaying detailed descriptions.

"Space bar"is used for command continuation, and"Return"executes the command or moves to the next line.

Correct usage example in classic CLI:

*A:SR1>config>router>interface# ?

- Shows all the valid commands and parameters under interface

BGP (Border Gateway Protocol)uses amulti-step decision processto select the best route among multiple paths. It doesnot use SPF or simple metrics like hop count.

Key BGP selection criteria include:

Local preference

AS path length

Origin type

MED (Multi-Exit Discriminator)

eBGP over iBGP

IGP metric to next hop

Option C is correct– BGP evaluatesmultiple attributesfor route selection.

In a typical MPLS/VPN service architecture:

PE (Provider Edge) router: Directly connects to thecustomer edge (CE)device.

P (Provider) router: Only forwards MPLS-labeled packets, doesnot touch customer routes.

LSR (Label Switch Router): General term, can be either PE or P depending on placement.

Correct Answer: A – PE

Itinterfaces with CE devicesandruns customer routing protocols(e.g., OSPF, BGP).