F5 201 Exam Questions Free Practice Test

Viewing page 6 out of 8 pages

Viewing questions 51-60 out of questions

Questions # 51:

Which two statements are true concerning the default communication between a redundant pair of BIG-IP systems? (Choose two.)

Options:

Synchronization occurs via a TCP connection using ports 683 and 684.

Connection mirroring data is shared via a TCP connection using port 1028.

Persistence mirroring data is shared via a TCP connection using port 1028.

Connection mirroring data is shared through the serial fail over cable unless network failover is enabled.

Expert Solution

Questions # 52:

Refer to the exhibit.

Question # 52

Which Pool Members are receiving traffic?

Options:

Serv1, serv2,serv3, serv4

serv1, serv3

serv1, serv3, serv4

serv1

Expert Solution

Questions # 53:

Which IP address will the client address be changed to when SNAT automap is specified within a Virtual Server configuration?

Options:

The floating self-IP address on the VLAN where the packet leaves the system.

The floating self-IP address on the VLAN where the packet arrives on the system.

It will alternate between the floating and non floating self-IP address on the VLAN where the packet leaves the system so that port exhaustion is avoided.

It will alternate between the floating and non floating self-IP address on the VLAN where the packet arrives on the system so that port exhaustion is avoided.

Expert Solution

Questions # 54:

Where is persistence mirroring configured?

Options:

It is always enabled.

It is part of a pool definition.

It is part of a profile definition.

It is part of a virtual server definition.

Expert Solution

Questions # 55:

Which statement accurately describes the difference between two loadbalancing modes specified as "member" and "node"?

Options:

There is no difference; the two terms are referenced for backward compatibility purposes.

When the loadbalancing choice references "node", priority group activation is unavailable.

Loadbalancing options referencing "nodes" are available only when the pool members are defined for the "any" port.

When the loadbalancing choice references "node", the addresses' parameters are used to make the loadbalancing choice rather than the member's parameters.

Expert Solution

Questions # 56:

Assuming other failover settings are at their default state, what would occur if the failover cable were to be disconnected for five seconds and then reconnected?

Options:

As long as network communication is not lost, no change will occur.

Nothing. Failover due to loss of voltage will not occur if the voltage is lost for less than ten seconds.

When the cable is disconnected, both systems will become active. When the voltage is restored, unit two will revert to standby mode.

When the cable is disconnected, both systems will become active. When the voltage is restored, both systems will maintain active mode.

Expert Solution

Questions # 57:

As a part of the Setup Utility, the administrator sets the host name for the BIG IP. What would be the result if the two systems in a redundant pair were set to the same host name?

Options:

Host names do not matter in redundant pair communication.

In a redundant pair, the two systems will always have the same host name. The parameter is synchronized between the systems.

The first time the systems are synchronized the receiving system will be assigned the same self-IP addresses as the source system.

When the administrator attempts to access the configuration utility using the host name, they will always connect to the active system.

Expert Solution

Questions # 58:

A BIG-IP Administrator explicitly creates a traffic group on a BIG-IP device.

Which two types of configuration objects can be associated with this traffic group? (Choose two.)

Options:

Pool Members

Virtual Addresses

iRules

VLANS

Application Instances

Expert Solution

Questions # 59:

Refer to the exhibit.

Question # 59

A user attempts to connect to 10.10.10.1.80 using FTP over SSL with an FTPS client. Which virtual server will match and attempt to process the request?

Options:

vsjutps

vs_ftp

vs_http

nvfs

Expert Solution

Questions # 60:

You have created a custom profile named TEST2. The parent profile of TEST2 is named TEST1. If additional changes are made to TEST1, what is the effect on TEST2?

Options:

All changes to TEST1 are propagated to TEST2.

Some of the changes to TEST1 may propagate to TEST2.

Changes to TEST1 cannot affect TEST2 once TEST2 is saved.

When TEST1 is changed, the administrator is prompted and can choose whether to propagate changes to TEST2.

Expert Solution

Viewing page 6 out of 8 pages

Viewing questions 51-60 out of questions

Pass the F5 F5-CA 201 Questions and answers with CertsForce