F5 201 Exam Questions Free Practice Test

Viewing page 5 out of 8 pages

Viewing questions 41-50 out of questions

Questions # 41:

A standard virtual server has been associated with a pool with multiple members. Assuming all other settings are left at their defaults, which statement is always true concerning traffic processed by the virtual server?

Options:

The client IP address is unchanged between the client side connection and the serverside connection.

The server IP address is unchanged between the client side connection and the serverside connection.

The TCP ports used in the client side connection are the same as the TCP ports serverside connection.

The IP addresses used in the clientside connection are the same as the IP addresses used in the serverside connection.

Expert Solution

Questions # 42:

What is the status of a pool member when manual resume is enabled and a health check first fails and then passes?

Options:

Offline (Disabled)

Offline (Enabled)

Available (Disabled)

Available (Enabled)

Expert Solution

Questions # 43:

A BIG-IP Administrator makes a configuration change to a Virtual Server on the Standby device of an HA pair. The HA pair is currently configured with Auto-Sync Enabled. What effect will the change have on the HA pair configuration?

Options:

The change will be undone when Auto-Sync propagates the config to the HA pair.

The change will be propagated next time a configuration change is made on the Active device.

The change will be undone next time a configuration change is made on the Active device.

The change will take effect when Auto-Sync propagates the config to the HA pair.

Expert Solution

Questions # 44:

A BIG-IP Administrator needs to restore an encrypted UCS archive from the command line using the

TMSH utility.

Which TMSH command should the BIG-IP Administrator use to accomplish this?

Options:

load/sys ucs passphrase

load/sys config file passphrase

load/sys config file

load/sys ucs no-license

Expert Solution

Questions # 45:

A local user account (Users) on the BIG-IP device is assigned the User Manager role. Userl attempts to

modify the properties of another account (User2), but the action fails. The BIG-IP Administrator can

successfully modify the User2 account.

Assuming the principle of least privilege, what is the correct way to allow User 1 to modify User2

properties?

Options:

Move User2 to the same partition as User1

Grant User1 administrative privileges

Move User to the same partition as User2.

Modify the partition access for User 1

Expert Solution

Questions # 46:

A BIG-IP Administrator uses a device group to share the workload and needs to perform service on a BIG-IP device currently active for a traffic group. The administrator needs to enable the traffic group to run on another BIG-IP device in the device group. What should the administrator do to meet the requirement?

Options:

Create a new Traffic Group and then fail to Standby Unit

Select Traffic Group and then select Failover

Select Traffic Group and then select Force to Standby

Select Traffic Group on Primary Unit and then select Demote

Expert Solution

Questions # 47:

When using the setup utility to configure a redundant pair, you are asked to provide a "Failover Peer IP". Which address is this?

Options:

an address of the other system in its management network

an address of the other system in a redundant pair configuration

an address on the current system used to listen for failover messages from the partner BIG-IP

an address on the current system used to initiate mirroring and network failover heartbeat messages

Expert Solution

Questions # 48:

Refer to the exhibit

The BIG-IP Administrator is unable to access the management console via Self-IP 10.10 1.33 and port 443.

What is the reason for this problem?

Options:

Packet Filter needs to be configured to allow a source

Self IP is configured to allow TCP All

Self IP is configured to allow UDP 443

Packet Filter is configured to allow port 443

Expert Solution

Questions # 49:

Which two methods can be used to determine which BIG-IP is currently active? (Choose two.)

Options:

The bigtop command displays the status.

Only the active system's configuration screens are active.

The status (Active/Standby) is embedded in the command prompt.

The ifconfig a command displays the floating addresses on the active system.

Expert Solution

Questions # 50:

Some users who connect to a busy Virtual Server have connections reset by the BIG-IP system. Pool member resources are NOT a factor in this behavior. What is a possible cause for this behavior?

Options:

The Connection Rate Limit is set too high

The server SSL Profile has NOT been reconfigured.

The Connection Limit is set too low.

The Rewrite Profile has NOT been configured.

Expert Solution

Viewing page 5 out of 8 pages

Viewing questions 41-50 out of questions

Pass the F5 F5-CA 201 Questions and answers with CertsForce