Pass the CWNP CWDP Wi-Fi Design CWDP-304 Questions and answers with CertsForce

Viewing page 6 out of 9 pages
Viewing questions 51-60 out of questions
Questions # 51:

A business traveler from North America is in Europe. The hotel only provides coverage in 2.4 GHz. The traveler connects to the hotel's SSID and notices an AP in the hotel room.

However, the laptop reports a very low RSSI when connected. The traveler does not have the same problem when connecting in the lobby.

What would be the most likely cause of the low RSSI in the hotel room?

Response:

Options:

A.

The AP in the room is transmitting on channel 13 and the traveler associated to a non-channel 13 AP located elsewhere.


B.

The AP in the room is using Bluetooth instead of Wi-Fi.


C.

The AP in the room is using ZigBee instead of Wi-Fi.


D.

The switchport that the AP is connected to is only capable of transmitting at 10 Mbps.


Expert Solution
Questions # 52:

Given: In a site survey deliverable report, you are expected to explain the spectrum measurements taken at the customers site. What portion of a

spectrum analyzer view can be used to determine if a given channel is too active for use as the active channel for a new AP?

Options:

A.

Device list


B.

Frame decode


C.

Real time FFT


D.

Duty cycle


Expert Solution
Questions # 53:

You desire to achieve a 450 Mbps MCS. What 802.11n features (from the numbered list below) are required?

1. Frame aggregation

2. Short GI

3. 40 MHz channels

4. 2 spatial streams

5. 3 spatial streams

6. Transmit beamforming (TxBF)

Options:

A.

2, 3, 2


B.

1, 2, 3, 5


C.

1, 2, 3, 4, 6


D.

2, 3, 5


Expert Solution
Questions # 54:

When performing a roaming test and packet capture at the same time, what are two particular frames that will be present when roaming between two APs is successful?

Options:

A.

Beacon and DTIM


B.

Probe Request and Probe Response


C.

Association Request and Association Response


D.

Reassociation Request and Reassociation Response


Expert Solution
Questions # 55:

What is the most suitable antenna option to be used when designing a WLAN infrastructure with APs mounted on a ceiling with a height of more

than 20 feet and having all of the client stations used from the floor?

Options:

A.

Patch


B.

Dish


C.

Grid


D.

Low-gain dipole


Expert Solution
Questions # 56:

You have performed a validation site survey after deploying a WLAN infrastructure that is an All-Wireless-Office. One specific application of your

customer is experiencing delay when using the application after moving from wired connectivity. After your validation, you realized that all APs are

using 80 MHz channel- widths instead of 20 MHz on the 5 GHz band, as it was designed. What can be done to resolve the delay on this

application?

Options:

A.

APs should be using 160 MHz channel-widths to get more throughput


B.

Reconfigure to use 20 MHz channel-widths, so reuse of the frequency is more effective


C.

Power-off half of the APs to reduce CCI and keep 80 MHz channel-widths


D.

Add more APs using 80 MHz channel-widths


Expert Solution
Questions # 57:

You are designing a WLAN and nave been asked to recommend a security solution for the network The organization requires that 802 1X/EAP be implemented, but they do not have a PKI and do not wish to deploy one They suggest that mostly Windows clients. Apple phones and Android phones will be used What do you recommend?

Options:

A.

Use CCMP AES with a PSK


B.

Use EAP-PEAP for the authentication solution


C.

Use FAP-TLS for the authentication solution


D.

Use TKIPRC4 with a PSK


Expert Solution
Questions # 58:

How are EAP messages transported over 802.11 wireless LANS?

Response:

Options:

A.

EAP-Fast


B.

PEAP


C.

EAPOL


D.

EAP_TLS


Expert Solution
Questions # 59:

Given: As the wireless network administrator for XYZ Company, you are planning to upgrade your aging wireless network infrastructure, as well as

some clients, to support 802.11ac. In your research, you have discovered that your new wireless client devices and infrastructure are 802.11ac,

WMM, and WMM-PS certified by the Wi-Fi Alliance. Some of your existing client devices are 802.11a/b/g devices that do not support WMM.

Given this information, what scenario is possible when your company's employees begin using both types of client devices on the new WLAN?

Options:

A.

All WMM-PS certified client devices will be prevented from utilizing WMM-PS features until all stations in use on the wireless medium are

WMM-PS certified.


B.

The WLAN infrastructure will set the dozing times of the WMM-PS certified client devices based upon their WMM access category, while the

non-WMM-PS client devices will continue to use PS-Poll frames.


C.

Performance and battery life will be inconsistent between WMM-PS and non-WMM-PS client devices when used with applications that

support WMM-PS.


D.

WMM-PS enabled APs will allow both WMM-PS and non-WMM-PS stations to use the trigger-and-delivery mechanism, but WMM-PS stations wil


Expert Solution
Questions # 60:

A table of VLANs in a _________ document should include what device performs ________ services.(Fill in the blanks)

Response:

Options:

A.

HLD, routing


B.

LLD, bridging


C.

LLD, routing


D.

HLD, QoS


Expert Solution
Viewing page 6 out of 9 pages
Viewing questions 51-60 out of questions