1. Home
  2. Cisco
  3. CCNP Data Center
  4. 300-615
  5. Troubleshooting Cisco Data Center Infrastructure (300-615 DCIT) Questions and Answers

Pass the Cisco CCNP Data Center 300-615 Questions and answers with CertsForce

 Cisco Exams      Go to Exam Detail      Get Premium Access
Viewing page 5 out of 5 pages
Viewing questions 41-50 out of questions
Questions # 41:

Refer to the exhibit.

Question # 41

The scheduler job fails to run. Which action resolves the issue?

Options:
A.

Change the file name.

B.

Configure the authentication credentials.

C.

Change the TFTP server address.

D.

Configure the RBAC authentication.

Expert Solution
Questions # 42:

Refer to an exhibit.

Question # 42

An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?

Options:
A.

Save the system image in NVRAM.

B.

Use the same system image as the kickstart image.

C.

Load a new system image.

D.

Reload the same system image.

Expert Solution
Questions # 43:

A Cisco uCs C-Series Server powers off due to a power outage. The server should turn on when the power is restored with a fixed delay of 3 minutes. However, it remained powered off for more than 3 minutes after the engineer powered it back online. Which two actions resolve the issue (Choose two.)

Options:
A.

Configure the power-restore-policy.

B.

Configure the power restore last-state policy.

C.

Set the delay value to 180.

D.

Set the delay fixed value to 3.

E.

Configure power sync policy.

Expert Solution
Questions # 44:

A customer configures HSRP between two data centers that are interconnected with OTV. The configuration succeeds, but traffic between two ESXi virtual hosts on the same site is routed suboptimally through the OTV overlay. Which two actions optimize the traffic? (Choose two.)

Options:
A.

Disable first-hop redundancy.

B.

Filter HSRP traffic by using a Layer 3 VACL on the OTV edge devices.

C.

Filter HSRP by using a Layer 2 MAC-list on the ESXi vSwitch.

D.

Filter HSRP traffic by using a Layer 3 VACL on the ESXi vSwitch.

E.

Filter HSRP by using a Layer 2 MAC-list on the OTV edge devices.

Expert Solution
Questions # 45:

An engineer must upgrade all components in a Cisco UCS domain to the same package version, but the upgrade process fails to complete. Which set of Auto Install actions resolves the problem?

Options:
A.

Install Infrastructure Firmware, then Install Server Firmware.

B.

Install infrastructure Firmware, then Install Hypervisor Firmware.

C.

Install Hypervisor Firmware, then Install Infrastructure Firmware

D.

Install Server Firmware, then Install Infrastructure Firmware

Expert Solution
Questions # 46:

Refer to the exhibit.

Question # 46

A network engineer finds one of the fabric interconnects offline when connecting L1 and L2 ports on both fabric interconnects. Which action resolves the issue?

Options:
A.

1. Connect to Fabric Interconnect B.

2. Verify the cluster status and HA election.

3. Validate Fabric Interconnect B hardware issues.

B.

1. Connect to Fabric Interconnect A.

2. Verify the cluster status and HA election.

3. Validate Fabric Interconnect A hardware issues.

C.

1. Connect Fabric Interconnect B and change the role to primary.

2. Reboot Fabric Interconnect B.

3. Add the Fabric Interconnect A as subordinate fabric to the cluster.

D.

1. Connect Fabric Interconnect B and execute “Erase configuration”

2. Reboot Fabric Interconnect B.

3. Add the subordinate Fabric Interconnect to the cluster.

Expert Solution
Questions # 47:

Refer to the exhibit.

Question # 47

The vPC neighborship between two switches is in suspended state. Which configuration change resolves the issue and brings up the vPC neighborship?

Options:
A.

Change STP Port Type to Network on the peer switch

B.

Enable Bridge Assurance on the local switches

C.

Configure QoS MTU value of 9216 on the peer switch

D.

Add VLAN 400-401 to the configuration on the local switch

Expert Solution
Questions # 48:

Refer to the exhibit.

Question # 48

The script fails to bring up Ethernet 1/2 when Ethernet 1/1 goes down. Which change

enables the script to run as intended?

Options:
A.

Set the port VLAN

B.

Include an action to manually shut down Ethernet 1/1

C.

Add an action to configure the terminal

D.

Configure an enable action

Expert Solution
Questions # 49:

The external routes fail to propagate to leaf switches in Cisco ACI fabric Which two actions resolve the issue? (Choose two.)

Options:
A.

Enable the VTEP pool in the fabric

B.

Assign an MP-BGP AS number to the fabric.

C.

Specify the spine nodes as route reflectors

D.

Associate the correct contract to the L30ut.

E.

Configure an MP-BGP area.

Expert Solution
Questions # 50:

Question # 50

Refer to the exhibit. A network engineer is troubleshooting a Cisco Nexus 5000 Series Switch. The interface between the server and the switch is nonoperational and is expected to operate at 10 Gbps. The drain rate of the interface is 3 Mbps. Which action resolves the issue?

Options:
A.

Configure pause error-disable recovery

B.

Enable link level pause on the interface

C.

Reset priority flow counters

D.

Set priority flow control pause

Expert Solution
Viewing page 5 out of 5 pages
Viewing questions 41-50 out of questions