Pass the Cisco CCNP Data Center 300-615 Questions and answers with CertsForce

Viewing page 3 out of 5 pages
Viewing questions 21-30 out of questions
Questions # 21:

Question # 21

Refer to the exhibit. The administrator set up two pairs of Cisco Nexus switches. The administrator set dfferent vPC priorities on all four Nexus switches. As soon as the administrator activates the vPC between the two pairs the network faces

different issues. The problems range from both Nexus pairs declare themselves as root bridge, as well as spanning-tree inconsistencies and traffic forwarding issues. Which action resolves these issues?

Options:

A.

Change the role priority on one pair.


B.

Configure peer-config-check-bypass on both pairs.


C.

Configure a vPC peer link between both peers.


D.

Change domain ID on one pair to a diferent ID.


Expert Solution
Questions # 22:

Refer to the exhibit.

Question # 22

The EEM script fails to send an SNMP trap when a user attempts to enter configuration mode. Which configuration is missing from the script?

Options:

A.

event statement


B.

event-default action statement


C.

policy-default action statement


D.

IP address of the SNMP server


Expert Solution
Questions # 23:

A server administrator attempts to change the Cisco IMC KVM certificate to one signed by a private CA, but the certificate is not being accepted. What can cause this process to fail?

Options:

A.

using a certificate with a password-protected private key


B.

RSA encryption being used in the generation of the certificate.


C.

AES encryption being used in the generation of the certificate.


D.

public IP addres of the Cisco IMC not being included in the SAN.


Expert Solution
Questions # 24:

A request to activate the port security database is rejected. Which action do you perform to investigate the cause of the issue?

Options:

A.

Enable the auto-learning feature.


B.

Use the force option to identify rejected devices.


C.

Find conflicting entries between the active and configuration databases.


D.

Verify that devices are fully attached to the active database.


Expert Solution
Questions # 25:

A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?

Options:

A.

Verify that the SFPs are supported.


B.

Change the SFP to operate at 4 Gbps instead of 2 Gbps.


C.

Run the shutdown and then no shutdown command on the interface.


D.

Run the switchport ignore bit-errors command on the interface.


Expert Solution
Questions # 26:

Refer to the exhibit.

Question # 26

After the configuration is performed, guestshell continues to use 2%CPU. Which action resolves the issue?

Options:

A.

Resync the database


B.

Recreate the guestshell


C.

Reboot the guestshell


D.

Reboot the switch


Expert Solution
Questions # 27:

An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)

Options:

A.

M-Series module


B.

ESSENTIALS license


C.

STORAGE-ENT license


D.

FCoE license


E.

F-Series module


Expert Solution
Questions # 28:

Refer to the exhibit.

Question # 28

A network engineer notices packet drops on FCoE traffic from the servers. Which action resolves the issue?

Options:

A.

Apply flowcontrol receive on the interface.


B.

Apply flowcontrol transmit on the interface.


C.

Enable priority flow control on the interface.


D.

Disable priority flow control on the interface.


Expert Solution
Questions # 29:

Refer to the exhibit.

Question # 29

An attempt to bind the Ethernet interface to vFC fails. Which action resolves the issue?

Options:

A.

Add the FCoE VLAN to the allowed VLAN list.


B.

Configure the FCoE VLAN that corresponds to the vFC VSAN as a private VLAN.


C.

Configure the interface as a trunk port.


D.

Configure the interface to use the native VLAN of the trunk port.


Expert Solution
Questions # 30:

Refer to the exhibit.

Question # 30

The FCoE traffic fails to traverse the vfc2 interface. The VSAN 102 is configured for vfc2. Which action resolves the issue?

Options:

A.

Enable LLDP on the interface vfc2


B.

Activate DCBX on the N9K switch


C.

Activate DCBX on the interface e101/1/2


D.

Enable LLDP on the neighbor switch


Expert Solution
Viewing page 3 out of 5 pages
Viewing questions 21-30 out of questions