Pass the AVIXA AVIXA Communications Certifications CTS Questions and answers with CertsForce

Network Address Translation (NAT) is a method used to translate the private IP addresses of computers within a local network to a single public IP address. This allows multiple devices on a local network to access external networks (such as the internet) using a single IP address, conserving the number of public IP addresses needed and providing a layer of security by masking internal IP addresses from the outside world.

Microphones produce very low voltage analog signals, typically in the millivolt range (often between 1-10 mV). These signals are then pre-amplified before further processing.

“Microphone-level signals are generally less than 1 volt and commonly measured in millivolts, requiring preamps to boost signal strength for processing.”

— CTS Exam Guide, Audio Signal Flow and Levels

The amount of air that moves through the credenza is crucial because AV equipment generates heat during operation. Proper ventilation ensures that the equipment does not overheat, which can cause damage and impact performance. Overheating can void warranties as manufacturers typically specify operational temperature ranges and ventilation requirements. Ensuring adequate airflow is a common stipulation in AV equipment warranties. Proper ventilation helps maintain optimal operating conditions, thereby protecting the equipment and upholding warranty terms.

A Responsibility Matrix (also called RACI) outlines who is responsible, accountable, consulted, and informed for each project task or deliverable. It helps eliminate ambiguity and aligns team expectations.

“A responsibility matrix details task ownership and accountability across stakeholders—essential for project clarity.”

— CTS Exam Guide, Project Management Documentation

"Shock Loads" for equipment mounts refer to sudden additional loads from earthquakes or personnel hanging from the mounts. Shock loads are unexpected forces that can be significantly higher than normal operating loads and can cause structural failures if not properly accounted for. This is particularly important in areas prone to seismic activity or where equipment might be subjected to additional stresses. Axis Technology Specialist documentation highlights the need to design mounts and supports to withstand such shock loads to ensure the safety and durability of the installation.

The best immediate workaround is to patch the input directly to the output, bypassing the switcher. This allows the system to continue functioning while a more permanent solution is found. It ensures that the client experiences minimal downtime and disruption. Changing the power supply or replacing the switcher are also viable options, but they may take more time and resources. Calling the manufacturer for support can also be part of the solution process, but it doesn't provide an immediate workaround.

Legibility of text on a display is directly related to the height of the characters. As the height increases, the text becomes easier to read from a distance because the characters are larger and more distinct. This is a fundamental principle in design and ergonomics, ensuring that text is easily readable for users in various viewing conditions. This is particularly important in contexts such as digital signage, user interfaces, and public information displays.

For optimal viewing comfort, the top of a display should not be positioned more than 30 degrees above the viewer’s line of sight. This guideline ensures that viewers do not have to strain their necks to see the entire screen. While Options A and B might seem reasonable, 30 degrees is considered the upper limit for comfortable viewing, with viewers ideally positioned to see the full display without needing to look up excessively.

CTS References: AVIXA CTS Exam Guide, Chapter on Display Mounting and Viewing Angles; CTS Handbook, Section on Ergonomic Viewing Considerations.

The fourth cable from the left (black coaxial cable)

The coaxial cable (the fourth cable from the left) is least susceptible to electromagnetic interference (EMI) due to its construction, which includes a central conductor surrounded by a shielding layer. This shielding, often made of metal foil or braided wire, effectively blocks external electromagnetic fields, preventing them from interfering with the signal.

Here’s a breakdown of each cable type:

Twisted Pair Cable (first from the left): Susceptible to EMI unless shielded, though twisted pairs can reduce interference somewhat.

Multi-conductor Cable (second from the left): More susceptible to EMI, depending on the shielding used.

Fiber Optic Cable (third from the left): Immune to EMI, as it transmits data as light rather than electrical signals.

Coaxial Cable (fourth from the left): Highly resistant to EMI due to its shielding, making it ideal for environments with significant electrical interference.

CTS Technology Specialist Reference

The CTS curriculum discusses the benefits of coaxial cable in environments with potential EMI due to its robust shielding properties. It’s often recommended for AV installations where EMI is a concern. Fiber optic, which is not affected by EMI, is another choice, but coaxial is traditionally favored for certain AV applications due to cost and compatibility.

The correct answer is the Air Plenum area — the space above the ceiling tiles used for air circulation in HVAC systems.

According to NFPA 70: National Electrical Code (NEC) and referenced in the AVIXA CTS Exam Guide, cabling run through plenum spaces must meet stringent fire and smoke safety standards. This is because if a fire occurs, the plenum area can rapidly spread smoke and toxic fumes throughout a building.

From the CTS Exam Guide (5th Edition), under Chapter 2: Infrastructure, it states:

“Plenum-rated cable is required in spaces used for environmental air (plenum spaces), as these cables are designed with fire-retardant jackets that emit low smoke. Non-plenum cable cannot be used unless it is enclosed in a conduit rated for plenum use.”

— AVIXA CTS Exam Guide, Chapter 2, p. 42–44