Pass the Veritas InfoScale VCS-260 Questions and answers with CertsForce

Viewing page 1 out of 3 pages
Viewing questions 1-10 out of questions
Questions # 1:

What is the state of a remote cluster if the connector process on a local cluster determines the remote cluster is down, but the remote cluster sends a response indicating it is running and connected to the local cluster?

Options:

A.

LOST_CONN


B.

UNKNOWN


C.

INQUIRY


D.

LOST_HB


Expert Solution
Questions # 2:

When run in a two node cluster, what does the lltstat -nvv command show?

Options:

A.

only LLT information for the node the command was run on


B.

LLT information for all configured nodes in the cluster


C.

LLT information for any cluster nodes attached to the same switch


D.

only LLT information for nodes verified by Veritas Cluster Server to be active


Expert Solution
Questions # 3:

An administrator needs to set up a service group dependency with the following characteristics:

The parent group depends on the child group being online on the same system. If the child group faults, the parent group should be taken offline. If the parent group faults, the child group should go offline.

Which type of dependency is this?

Options:

A.

online local soft


B.

online global hard


C.

online local hard


D.

online site firm


Expert Solution
Questions # 4:

Which two capabilities must an application have in order to be made highly available using Veritas Cluster Server? (Select two.)

Options:

A.

The ability to monitor each instance of the application independently


B.

The ability to be installed on shared storage


C.

The ability to determine if the application is running


D.

The ability to notify the administrator of the state


E.

The ability to disconnect users from the application


Expert Solution
Questions # 5:

An administrator is adding a node to a running cluster. The administrator has successfully installed Veritas Cluster Server and has configured and started LLT.

Which command will allow the new node to start communicating with the cluster?

Options:

A.

gabconfig -c


B.

hastart


C.

sh /etc/gabconfig


D.

hastart -force


Expert Solution
Questions # 6:

An administrator is bringing a service group online. One of the resources is remaining offline, and is shown in waiting to go online state. Which command should the administrator run to stop Veritas Cluster Server from attempting to bring the resource online to troubleshoot the issue?

Options:

A.

hares -clear


B.

hares -offline


C.

hagrp -offline


D.

hagrp -flush


Expert Solution
Questions # 7:

Which command should an administrator perform to transition a resource state from * waiting to go online' to ‘not waiting' if the operation hangs on a particular resource?

Options:

A.

hagrp -flu3h


B.

hagrp —flush —force


C.

hares -flushinfo


D.

hares —clear


Expert Solution
Questions # 8:

A cluster is configured to use coordination point servers for data protection.

What happens to the service groups if connectivity between one of the nodes and the coordination point servers is lost?

Options:

A.

The service groups fail over to systems that remain connected to the coordination point servers.


B.

The service groups remain online, but offline groups are unable to come online.


C.

The service groups remain online and related messages are logged.


D.

The service groups are taken offline until connectivity is resumed with the coordination point servers.


Expert Solution
Questions # 9:

When is the restate change trigger unable to detect a resource state transition?

Options:

A.

when a resource is faulted


B.

when a resource is brought online


C.

when a resource is enabled


D.

when a resource fault is cleared


Expert Solution
Questions # 10:

Which resource type can an administrator use to mirror the state of another persistent resource?

Options:

A.

Phantom


B.

Proxy


C.

VolumeSet


D.

NotifierMngr


Expert Solution
Viewing page 1 out of 3 pages
Viewing questions 1-10 out of questions