1. Home
  2. Nokia
  3. SRC Certification
  4. 4A0-104
  5. Alcatel-Lucent Services Architecture Questions and Answers

Pass the Nokia SRC Certification 4A0-104 Questions and answers with CertsForce

 Nokia Exams      Go to Exam Detail      Get Premium Access
Viewing page 3 out of 9 pages
Viewing questions 21-30 out of questions
Questions # 21:

Which of the following statements best describes the flooding of traffic on a PE when traffic is received on a spoke SDP?

Options:
A.

Traffic is flooded to all SAPs in the service.

B.

Traffic is flooded to all SAPs and spoke SDPs in the service.

C.

Traffic is flooded to all SAPs and mesh SDPs in the service.

D.

Traffic is flooded to all SAPs, spoke SDPs, and mesh SDPs in the service

E.

The traffic is not flooded.

Expert Solution
Questions # 22:

Click on the exhibit button below.

Question # 22

Assuming the customer only needs to monitor traffic from PE3 to the customer site, what three items are missing from PE3's configuration? (Assume that the IP/MPLS network structure between the local and remote PEsis in place.)

Options:
A.

The mirror destination configuration on PE5 is missing the "remote-source" command,

B.

The mirror destination on PE3 needs a "remote-source" command.

C.

The mirror service IDs on the local and remote destinations must match.

D.

The mirror source on PE3 needs a "remote-source" command.

E.

The mirror source command on the remote PE3 needs a command that tells it to monitor port 1/1/2.

Expert Solution
Questions # 23:

Which of the following statements are TRUE about configuring a SDP between an IES and a VPLS? (Choose 2)

Options:
A.

The SDP must be a mesh

B.

The SDP must be a spoke.

C.

Once the SDP is configured on both PE routers, both the services will be operationally up without further configuration changes.

D.

The Layer 2 MTUs must match between the IES and the VPLS

E.

The Layer 2 MTU must be 14 bytes smaller on the VPLS than it is on the IES.

Expert Solution
Questions # 24:

Which tree in the CLI would you need to be in to add a QoS policy to a SAP?

Options:
A.

config>router#

B.

config>qos#

C.

config>port#

D.

config>service#

Expert Solution
Questions # 25:

Which of the following tasks must be carried out before deleting an Epipe service? (Choose 4)

Options:
A.

Shut down all SAPs associated with the service.

B.

Shut down all SDPs associated with the service.

C.

Delete all SAPs and SDPs associated with the service.

D.

Shut down all physical ports that are bound to a SAP.

E.

Delete the Customer ID.

F.

Shut down the service.

Expert Solution
Questions # 26:

VPWS allows carriers to offer services such as point-to-point frame-relay, ATM, and Ethernet on a single platform without the need for multiple overlay networks.

Options:
A.

TRUE

B.

FALSE

Expert Solution
Questions # 27:

Which of the following statements best describes a route target?

Options:
A.

A route target is a BGP extended community used to identify the VRF table for a prefix at the receiving PE

B.

A route target is a mechanism from which VPRN controls the distribution of VPN routing information.

C.

Route target attributes are earned in a MP-BGP as attributes of the route.

D.

A route target is used by the PE router to identify the VRF that a VPN-lPv4 prefix is associated with.

E.

All of the above statements describe a route target

F.

None of the above statements describe a route target

Expert Solution
Questions # 28:

A service can be either local or distributed.

Options:
A.

TRUE

B.

FALSE

Expert Solution
Questions # 29:

Which OAM command can be used to verify the correct and consistent provisioning of a service between two service end points?

Options:
A.

sdp-ping

B.

Isp-ping

C.

sap-ping

D.

svc-ping

Expert Solution
Questions # 30:

Which of the following most accurately describes the default behavior of a VPLS regarding the handling of a tagged frame at the ingress ofSAP1/1/1:100?

Options:
A.

The FCS is verified and the customer frame is transported intact over the service provider network.

B.

The FCS is verified and kept in the customer frame. The VLAN tag is removed for transport over the network.

C.

The FCS is verified and removed from the frame. The VLAN tag is kept for transport over the network.

D.

The FCS is verified and removed from the frame. The VLAN tag is removed for transport over the network.

Expert Solution
Viewing page 3 out of 9 pages
Viewing questions 21-30 out of questions