Pass the NFPA Fire Protection Specialist CFPS Questions and answers with CertsForce

The correct answer is A. Type I construction consists of structural members of approved noncombustible or limited combustible materials with specified fire resistance ratings for exterior bearing walls of 3 or 4 hours. This is the highest level of fire resistance among the five types of construction defined by NFPA 220: Standard for Types of Building Construction.Type I construction is typically used for high-rise buildings made of concrete and protected steel12

When magnesium shavings or chips come in contact with water, they react to produce magnesium hydroxide and hydrogen gas. The chemical equation for the reaction is: 2 Mg (s) + 2 H2O (l)→2 Mg (OH)2 (aq) + H2 (g). This displacement reaction is characterized by effervescence, a vigorous reaction, and the formation of a white precipitate of magnesium hydroxide.

References:

Reactions of Group 2 Elements with Water - Chemistry LibreTexts1

Magnesium (Mg) and water - Lenntech2

Cellulose nitrate products begin to decompose at about 300 °F (150 °C). This is the temperature at which the nitrate ester bonds start to break down and release nitric acid, which further catalyzes the decomposition. The decomposition temperature depends on the nitrogen content, the stabilizers, and the external heating rate of the cellulose nitrate. Higher nitrogen content, lower stabilizer concentration, and faster heating rate lower the decomposition temperature and increase the risk of thermal runaway.

References:Nitrocellulose - Wikipedia;Comparative analysis of stable decomposition and combustion kinetics of nitrated cellulose;Degradation of aged nitrocellulose investigated by thermal analysis methods;Nitrocellulose;Effect of stabilizers and nitrogen content on thermal properties of nitrocellulose

Hazardous waste

Explore

The correct answer is C. Environmental Protection Agency (EPA) standards require solid waste be treated as hazardous if it is a listed waste and/or meets the characteristics prescribed by the standard for toxicity, reactivity, corrosivity, andignitability.A listed waste is a waste that appears on one of the four lists of hazardous wastes in the Code ofFederal Regulations (CFR) part 261 subpart D1.A characteristic waste is a waste that exhibits one or more of the following traits: toxicity, reactivity, corrosivity, or ignitability2. Toxicity is the ability of a waste to leach harmful chemicals into the environment. Reactivity is the tendency of a waste to undergo violent chemical reactions or generate toxic gases. Corrosivity is the property of a waste to corrode metals or damage living tissues.Ignitability is the capacity of a waste to catch fire under certain conditions2.These characteristics are defined by specific tests and criteria in the CFR part 261 subpart C3.The EPA standards for hazardous waste are based on the Resource Conservation and Recovery Act (RCRA), which is the federal law that regulates the management of solid and hazardous waste in the United States4.

Class 3 unstable reactive gas is defined as a material that in itself is capable of detonation or explosive decomposition or reaction at normal temperatures and pressures with a strong initiating source or if heated under confinement. This class of gas readily undergoes violent chemical change at elevated temperatures and pressures.

References:NFPA 55: Compressed Gases and Cryogenic Fluids Code, 2016 Edition, Section 3.3.51.14.3;International Fire Code, 2015 Edition, Appendix E, Section E102.1.1

Wet chemical extinguishing agents, such as potassium acetate and potassium citrate, when sprayed on a grease fire, extinguish the fire by smothering and cooling. The wet chemical agent reacts with the hot grease and forms a layer of soap-like foam on the surface of the fat, which acts as an insulation between the hot grease and the atmosphere, preventing the escape of combustible vapors and oxygen supply.The wet chemical agent also absorbs heat from the grease and lowers its temperature below the ignition point12

References:

What is the Difference Between a Wet and Dry Chemical Fire …

Wet Chemical (Class K) Fire Extinguisher - Portable - WFX

20 years.

According to NFPA 25, Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems, 2020 edition, fast response sprinklers are those that have a response time index (RTI) of 50 (m·s)^(1/2) or less.These sprinklers are designed toactivate faster than standard response sprinklers in the event of a fire, and they are typically used in light hazard, ordinary hazard, and residential occupancies1

NFPA 25 requires initial testing of representative samples of fast response sprinklers after 20 years from the date of manufacture, and subsequent testing every 10 years thereafter. The testing involves removing a minimum of four sprinklers or 1% of the total number of sprinklers per individual sprinkler sample, whichever is greater, and sending them to a recognized testing laboratory. The laboratory will perform a plunge test, which measures the time it takes for the sprinkler to operate when exposed to a specified air temperature.The test results will indicate whether the sprinklers meet the acceptance criteria or need to be replaced123

References:

NFPA 25: Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems1

Sprinkler System Inspections, Testing, and Maintenance Frequencies Explained | NFPA4

Sprinkler Testing on Quick Response Sprinklers: What You Need to Know2

NFPA 25 ITM Quick Reference Guide - hillgrp.com3