1. Home
  2. Huawei
  3. HCIE-Storage
  4. H13-629
  5. HCIE-Storage (Written) Questions and Answers

Pass the Huawei HCIE-Storage H13-629 Questions and answers with CertsForce

 Huawei Exams      Go to Exam Detail      Get Premium Access
Viewing page 1 out of 11 pages
Viewing questions 1-10 out of questions
Questions # 1:

The iSCSI protocol is mapped on the TCP protocol. For a TCP encapsulation of the iSCSI protocol packet, which of the following parts are not included?

Options:
A.

TCP Header

B.

IP Header

C.

ISCSI Header

D.

ISCSI data

Questions # 2:

Which of the OceanStor V3 file system remote replication descriptions are correct? (Multiple choice.)

Options:
A.

It is an object-based approach to data replication

B.

ROW snapshots are based on the cyclical manner of data replication

C.

It can be manually set off by the user or system timing synchronization starting

D.

It supports the Quota quota information of the main file system to the slave, no need to configurethe quota.

Questions # 3:

Which of the following copy is supported by OceanStor V3 remote file system?

Options:
A.

Synchronous and asynchronous replication

B.

Simultaneous replication

C.

Asynchronous replication

D.

support multiple file system consistency replication

Questions # 4:

Assuming a customer's initial backup capacity of 1TB, the average daily data increment of 10G, with a backup strategy of once a week for all the equipment once a day from Tuesday toSunday.

All reserve and additional backup data are stored for 4 weeks, regardless of deduplication / redundancy ratio / replication, etc. Calculate the required back-end.

The capacity should not be less than ______. This 1TB is calculated according to 1000G.

Options:
A.

4940G

B.

4280G

C.

5940G

D.

5280G

Questions # 5:

The Redhat Linux Enterprise 6 cp command is used to complete the operating system data migration. What steps are needed to verify the transfer? (Multiple choice.)

Options:
A.

Check if the size of the migrated file is the same as the original data.

B.

Check if the number of documents corresponds to the original data

C.

Check if each file with read and write permissions corresponds to the original data

D.

Whether the time for reviewing the case file corresponds to the original data.

Questions # 6:

During the migration of SAN storage by LVM from AIX, the data migration designer is in a very important stage. Prior to accessing new devices, there are a number of issues that needs to be considered to help with data migration design, including: (Multiple choice.)

Options:
A.

This device can not / should not be connected to an existing SAN.

B.

AIX system how to connect to the new storage device.

C.

How AIXsystems and data can be migrated from the old disk to the new disk.

D.

The format of the file system, whether the file group is compatible with the new device volume.

Questions # 7:

HPUX system has two user volume groups: VG01 and VG02. If you execute the following commands:

vgexport-v-s-p -m /tmp/vg01.map / dev / vg01 and vgexport-v -s -m /tmp/vg01.map / dev / vg02.

What will be available using vglist to view the volume?

Options:
A.

vg01

B.

vg02

C.

vg01 vg02

D.

empty

Questions # 8:

In a Huawei OceanStor 18000 the engine, SVP, diskenclosure, and PCIe switch interconnections must be in accordance with certain rules and order. Which of the following statement is incorrect?

Options:
A.

The SVP needs to connect multiple engines through two PCI-e switches, and each engine's controller needs to be connected to a PCIe switch to ensure that the link redundancy provides reliability.

B.

When the control plane is connected to the network, when the engine and the PCIe switch are interconnected, the port P0 of the A3 slot and the PCI switch PCI port canbe used pick up.

C.

Huawei OceanStor 18000 can be used to install SAS interface modules and interconnect disk enclosures in slot 0 and slot 5 of the Huawei OceanStor 18000.

Questions # 9:

In a A VTL6900-I system, the backup server connected to it is the Linux operating system. The backup server and the VTL6900-I system are directly connected through the FC.

The server identifies the device information as shown below. After the backup server is configured as a backup client for the VTL6900-I system and the backup VTL system on the server virtual library process, which the following operation and description is correct:

(Multiple choice.)

Options:
A.

When configuring the backup client on the VTL side, you need to know that the WWPN of the FC port that connects the VTL to the VTL is available on the server in the sys /class / fc_host directory and subdirectory to the corresponding WWPN port.

B.

Server-sideidentification has been detected with the library device command is cat / proc / scsi / scsi.

C.

As shown in the figure, among the devices identified on the server side, the device labeled 1 is the scanned library.

D.

As shown in the figure, of the devices identified on the server side, the device labeled 2 is the information for the scanned tape.

Questions # 10:

Which of the following best practice descriptions of Oralce database is correct? (Multiple choice.)

Options:
A.

OLAP business query output is usually a statistical value (using group by with order by), soyou can set a larger SGA-target value (relative to OLTP).

B.

It is recommended to use UDEV UUID and drive letter binding, in Linux environment configuration Oracle database, to avoid subsequent maintenance letter changes caused by the database which can not start.

C.

If the database OLTP business log write is very frequent, it is recommended that the appropriate online log file up, but it is recommended not to exceed 128MB.

D.

In Windows2008 or windows2012 operating system environment, in order to improve I/ O processing efficiency, MBR partition is created, and diskpart command is recommended to set the partition alignment.

Viewing page 1 out of 11 pages
Viewing questions 1-10 out of questions