1. Home
  2. EMC
  3. No Cert Assigned
  4. DES-1241
  5. Specialist - Platform Engineer PowerStore Exam Questions and Answers

Pass the EMC No Cert Assigned DES-1241 Questions and answers with CertsForce

 EMC Exams      Go to Exam Detail      Get Premium Access
Viewing page 1 out of 3 pages
Viewing questions 1-10 out of questions
Questions # 1:

A Storage Administrator needs to address specific fixes within their Dell EMC PowerStore system. Which NDU software upgrade option is used for this situation?

Options:
A.

Hotfixes

B.

vCenter

C.

Drive firmware

D.

Software releases

Questions # 2:

Which component is a CRU?

Options:
A.

Base enclosure

B.

Expansion enclosure

C.

Battery Backup Unit

D.

Nodes

Questions # 3:

A Storage Administrator encounters a Snapshot issue on a Dell EMC PowerStore X system.

The administrator engages support and they determine the Snapshot issue is a known code bug within the OS version of PowerStore code. How can support address the problem in a timely manner?

Options:
A.

Disable the Snapshots feature to avoid encountering the code bug

B.

Upgrade the Snapshot portion of code within the OS

C.

Upgrade the PowerStore with a hotfix that corrects the code bug

D.

Wait for a new full OS release that corrects the code bug

Questions # 4:

What does the output of the command “svc_diag list --basic” show?

Options:
A.

Failover status

B.

Master_appliance_ID

C.

License status

D.

Boot mode

Questions # 5:

While on-site troubleshooting a Dell EMC PowerStore system, the node В embedded module fault LED is blinking blue and amber alternating at one second intervals. What does this indicate?

Options:
A.

Node is in degraded mode

B.

Node is booting

C.

Node is on service mode

D.

System is not initialized

Questions # 6:

What is the result of setting a VLAN ID of 0 on a network when running ICW for Dell EMC PowerStore?

Options:
A.

Network will pass tagged traffic

B.

Static route is set

C.

Network will pass untagged traffic

D.

Default route is set

Questions # 7:

What is a step in configuring the ToR data switches for a Dell EMC PowerStore T?

Options:
A.

Configure a port for the discovery laptop

B.

Create VLANs for NAS servers

C.

Create VLAN for vMotion networks

D.

Configure ports for management on native VLAN

Questions # 8:

While on-site installing a Dell EMC PowerStore T system, the node A embedded module management Ethernet port link LED is off. What does this indicate?

Options:
A.

Network connection is established

B.

No network connection is established

C.

Port speed is 1 GB/s

D.

Port speed is 10 GB/s

Questions # 9:

What describes Dell EMC PowerStore X front-end cabling?

Options:
A.

Uses internal VMware virtual switching and does not require a management network

B.

Storage and management use the same LACP bonded cable connection

C.

Uses VLTi data switch interconnectivity to support vMotion networks

D.

Management and discovery use the same cables and connections as storage

Questions # 10:

A Storage Administrator has an existing single appliance Dell EMC PowerStore 3000T cluster. An additional PowerStore 9000T has been purchased to add into the existing cluster.

How does the administrator proceed?

Options:
A.

Additional VLTi links on the ToR switching must be configured for the 9000T to support the increased inter-switch network load

B.

Add the new 9000T appliance into the cluster per the procedure; mixed models of the same type are supported

C.

Remove two of the four NVMe NVRAM drives from the 9000T the caching configuration of all clustered appliances must match

D.

The new appliance cannot be added to the cluster; appliance model and type must match when clustering appliances together

Viewing page 1 out of 3 pages
Viewing questions 1-10 out of questions