Pass the Cisco CCNP Data Center 300-615 Questions and answers with CertsForce

The selected answer, 1. Connect Fabric Interconnect B and execute “Erase configuration” 2. Reboot Fabric Interconnect B. 3. Add the subordinate Fabric Interconnect to the cluster, follows Cisco UCS operational logic. UCS Manager is policy-driven, so troubleshooting must determine whether the problem is caused by hardware discovery, service profile association, firmware activation, boot order, storage presentation, or management integration. The scenario points to fabric interconnect; that is why the selected action fixes the root condition rather than merely restarting the server. The wrong options either affect a different policy, require unnecessary disruption, or assume that physical connectivity alone is sufficient. Cisco documentation for UCS server boot and firmware management stresses that boot policies must include the correct target details, firmware workflows must complete their FSM stages, and hardware changes often require acknowledgement or re-acknowledgement before UCS Manager uses the new inventory. After remediation, the engineer should confirm that the UCS fault is cleared, the server association or discovery state is complete, and the operating system or management service can use the intended path.

The correct remediation is Change domain ID on one pair to a different ID. In Cisco data center troubleshooting, the first priority is to isolate whether the failure is caused by the underlay, overlay control plane, first-hop gateway behavior, or a consistency parameter. This item is centered on vPC, Cisco Nexus, so the selected action targets the condition that prevents normal forwarding rather than masking the symptom. Cisco Nexus and ACI guidance treats vPC, VXLAN EVPN, OTV, OSPF, BGP, HSRP, and LACP issues as state-dependent technologies: a neighbor, peer, VLAN, VNI, multicast group, timer, MTU, or policy mismatch can leave the protocol partially operational while traffic is still dropped. The rejected alternatives either change unrelated attributes, introduce a new inconsistency, or affect only a secondary behavior. The operational check after applying the fix should be to confirm adjacency or peer state, validate the relevant route/MAC/endpoint table, and test traffic in the affected VLAN or VRF. This aligns with Cisco DCIT network troubleshooting methodology for isolating control-plane state before changing data-plane policy.

The correct action is Span the traffic from the Eth 1/2 of the primary fabric interconnect. Cisco UCS troubleshooting depends on the relationship between policy, inventory discovery, firmware state, and server identity. The question involves UCS, fabric interconnect, IOM, so the selected option fixes the UCS component or policy that directly controls the failure. In UCS Manager, service profiles, vNIC/vHBA templates, boot policies, firmware packages, server pools, adapters, fabric interconnects, and I/O modules are applied through a managed model; a server can fail even when basic IP reachability exists if the relevant policy is incomplete or the hardware inventory has not been acknowledged correctly. The distractors typically change an unrelated object, force a disruptive recovery without fixing the policy, or apply to a different UCS mode. Cisco guidance is to verify faults, FSM stage, inventory status, association status, and the specific boot or connectivity policy before taking action. After the remediation, validate that the fault clears, the FSM completes, and the server or fabric component returns to the expected operable state.

Use a predefined local disk configuration policy is the correct fix under Cisco SAN troubleshooting practice. The issue described involves service profile, SAN boot, where the operating state depends on the correct combination of port type, VSAN, fabric service, and access-control database. MDS and Nexus SAN features do not infer missing policy: if the active zoneset, fabric-binding database, fcdomain, NPIV setting, or FCoE/LLDP negotiation is wrong, the link may come up physically but the initiator will not reach the target. The selected answer corrects the missing or mismatched element. The remaining choices either act at the wrong layer, change a non-causal parameter, or provide only a temporary reset. After applying the fix, a proper Cisco validation path is to review show interface, show flogi database, show fcns database, show zoneset active, and any isolation or merge-failure logs. That confirms the storage network is operationally consistent.

Cisco troubleshooting logic supports Detach the association with the no role command within the feature-group configuration mode as the required fix. In this question the symptoms point to Cisco Nexus, and the defect is best handled by correcting the exact control-plane or consistency condition. Nexus platforms can show interfaces or peers as configured while still refusing to forward traffic if a vPC Type-1 parameter, VLAN allowance, MTU, HSRP version, EVPN route, or routing attribute is wrong. Cisco methodology is to avoid broad resets unless the state machine is stuck; instead, correct the mismatched parameter and verify that the resulting operational state becomes stable. The other choices do not remove the root cause, or they modify a setting that is not used by the failing protocol exchange. After the change, the engineer should review the peer status, route or MAC table, and counters for drops or inconsistency messages. That sequence proves that the network fabric is fixed, not merely restarted.

Enable the peer-gateway feature is correct because the failure is an operations-plane condition involving HSRP. In Cisco data center products, management functions depend on more than IP connectivity. AAA servers must return the correct attributes, RBAC must map users to the correct security domain or role, certificates must be trusted and valid for the access method, and firmware or registration workflows must satisfy documented prerequisites such as NTP and required ports. The selected answer corrects that dependency. The distractors are not root-cause fixes because they either target a different subsystem or change a setting that would not influence the observed login, registration, warning, or fault. After the change, validation should include a successful login or registration test, review of the audit/fault record, and confirmation that the expected administrative scope is enforced. That approach matches Cisco operational troubleshooting for DCIT environments. The final check is to document the before-and-after state so the remediation is tied to a repeatable Cisco troubleshooting symptom rather than an assumed fix.