1. Home
  2. Brocade
  3. Interworking
  4. 150-130
  5. Brocade Certified Network Engineer 2012 Questions and Answers

Pass the Brocade Interworking 150-130 Questions and answers with CertsForce

 Brocade Exams      Go to Exam Detail      Get Premium Access
Viewing page 1 out of 4 pages
Viewing questions 1-10 out of questions
Questions # 1:

You are requested to design a network that requires a minimum of five subnets with a minimum of 16 hosts per subnet.

With the class C network of 200.101.192.0, which subnet mask would be used to fulfill these requirements?

Options:
A.

/25

B.

/26

C.

/27

D.

/28

Questions # 2:

What are two valid ways to represent the IPv6 address 2001:0000:0000:0200:002D:D0FF:FE48:4672? (Choose two.)

Options:
A.

2001::02:002D:D0FF:FE48:4672

B.

2001:0:0:0200:002D:D0FF:FE48:4672

C.

2001::0200:002D:D0FF:FE48:4672

D.

21::0200:002D:D0FF:FE48:4672

Questions # 3:

Which two statements about ICL links in Brocade Multi-Chassis Trunk (MCT) implementations are true? (Choose two.)

Options:
A.

ICL links connect the two MCT chassis and allows MCT clients to see both devices as a single device.

B.

ICL links connect the MCT client devices to the MCT logical chassis.

C.

ICL links are necessary for the two devices to form an MCT cluster.

D.

ICL links allow the MCT logical chassis to communicate with a non-MCT device.

Questions # 4:

Which two results does the link-aggregate configure key command accomplish when creating Link Aggregation Groups (LAGs) on a FastIron device? (Choose two.)

Options:
A.

It encrypts the LAGs for security,

B.

It identifies LAG membership.

C.

It allows multiple LAGs to be configured on a device.

D.

It is used to configure VLANs on the LAG.

Questions # 5:

A client had ports 1/3/1 and 1/3/2 on the Brocade FCX go down because of errors being received from the upstream switch. The client repaired the upstream switch but the ports of the FCX are still down.

Referring to the command output shown above, what does the client need to do to bring up the links?

Options:
A.

Enable the ports.

B.

Restart spanning tree.

C.

Restart the routing protocol.

D.

Reseat the cables for each port.

Questions # 6:

What happens to Ethernet frames that enter a switch with MAC learning disabled on all interfaces?

Options:
A.

AII incoming frames will be dropped.

B.

AII incoming frames will be flooded.

C.

Unicast frames will be dropped; multicast and broadcast frames will be flooded.

D.

Multicast and broadcast frames will be dropped; unicast frames will be flooded.

Questions # 7:

An identical route has been discovered by OSPF and RIP. By default, the OSPF route is chosen and added to the routing table. What should be done to allow the RIP route to be preferred?

Options:
A.

Redistribute OSPF routes into RIP.

B.

Change the administrative distance.

C.

Raise the route's priority in RIP.

D.

Use the no router OSPF command.

Questions # 8:

What are two methods that a Brocade device can be configured for load sharing? (Choose two.)

Options:
A.

per port

B.

per packet

C.

hash based

D.

per second

Questions # 9:

You are implementing an OSPF network with five defined areas. You want to configure OSPF area route sharing to other specified OSPF areas.

Which router will you need to configure to share area routes with other area routes?

Options:
A.

ABR router

B.

BDR router

C.

DR router

D.

BGP router

Questions # 10:

Which two Brocade products are recommended for core/aggregation use? (Choose two.)

Options:
A.

BrocadeMLXe

B.

Brocade FastIron WS

C.

Brocade NetIron CER 2000

D.

Brocade FastIron SX

Viewing page 1 out of 4 pages
Viewing questions 1-10 out of questions