Pass the RedHat RHCE RH302 Questions and answers with CertsForce

The LVM system organizes hard disks into Logical Volume (LV) groups. Essentially, physical hard disk partitions (or possibly RAID arrays) are set up in a bunch of equal-sized chunks known as Physical Extents (PE). As there are several other concepts associated with the LVM system, let's start with some basic definitions:

Physical Volume (PV)is the standard partition that you add to the LVM mix. Normally, a physical volume is a standard primary or logical partition. It can also be a RAID array.

Physical Extent (PE)is a chunk of disk space. Every PV is divided into a number of equal sized PEs. Every PE in a LV group is the same size. Different LV groups can have different sized PEs.

Logical Extent (LE)is also a chunk of disk space. Every LE is mapped to a specific PE.

Logical Volume (LV)is composed of a group of LEs. You can mount a filesystem such as /home and /var on an LV.

Volume Group (VG)is composed of a group of LVs. It is the organizational group for LVM. Most of the commands that you'll use apply to a specific VG.

1.Verify the size of Logical Volume:lvdisplay /dev/vg0/lv1

2.Verify the Size on mounted directory:df –h or df –h mounted directory name

3.Use :lvextend –L+400M /dev/vg0/lv1

4. resize2fs /dev/vg0/lv1to bring extended size online.

5. Again Verify using lvdisplay and df –h command.

Do the following steps as:

1. /proc is the virtual filesystem, we use /proc to modify the kernel parameters at running time.

# echo “1” >/proc/sys/net/ipv4/ip_forward

2. /etc/sysctl.confwhen System Reboot on next time, /etc/rc.d/rc.sysinit scripts reads the file /etc/sysctl.conf. To enable the IP forwarding on next reboot also you need to set the parameter.

net.ipv4.ip_forward=1

Here 0 means disable, 1 means enable.

By Default system accept the logs only generated from local host. To accept the Log from other host configure:

vi /etc/sysconfig/syslog

SYSLOGD_OPTIONS="-m 0 -r"

Where

-m 0 disables 'MARK' messages.

-r enables logging from remote machines

-x disables DNS lookups on messages recieved with -r

service syslog restart

You should know about the /etc/inittab file, where default runlevel will define. And Much more runlevel specific Scripts are called here.

Actually that problem will occur if you don’t specify the default runlevel.

Reboot the system

Boot the System on single user mode.

Except for a normal boot of Linux, single-user mode is the most commonly used option. This is the system maintenance mode for experienced Linux administrators. It allows you to perform clean backups and restores to any partitions as needed from local hardware. It also allows you to run administration commands, recover or repair password and shadow password files, run filesystem checks, and so forth.

vi /etc/inittab and Write

id:runlevel:initdefault:

Standard Runlevels in RedHat Enterprise Linux

Runlevel

Description

0

Halt

1

Single-user mode, for maintenance (backups/restores) and repairs

2

Multiuser, without networking

3

Multiuser, with networking

4

Unused

5

X11, defaults to a GUI login screen. Logins bring the user to a GUI desktop.

6

Reboot (never set initdefault in /etc/inittab to this value!)

To understand the role of a boot loader, take a step back from Linux. When you boot your computer, the BIOS starts by detecting basic hardware, including your hard drives. Once it's done, it looks for the boot loader on the Master Boot Record of the first available disk. If you're working with an older PC, the BIOS can't find your boot loader unless it's located within the first 1,024 cylinders of the hard disk.

Newer BIOSes overcome this problem with Logical Block Addressing, which is also known as LBA mode. LBA mode reads 'logical' values for the cylinder, head, and sector, which allows the BIOS to 'see' a larger disk drive.

If you have multiple hard drives, there is one more caveat. If your drives are IDE hard drives, the /boot directory must be on a hard drive attached to the primary IDE controller. If your drives are all SCSI hard drives, the /boot directory must be located on a hard drive with SCSI ID 0 or ID 1. If you have a mix of hard drives, the /boot directory must be located on either the first IDE drive or a SCSI drive with ID 0. In other words, this is not an issue on the Red Hat exams unless the computer that you're tested on has more than two hard drives. And I believe that's less likely, as that would increase the cost of the exam.

If you are getting the Kernel panic error, it means it is boot loader related problem. Redhat Enterprise Linux uses the GRUB boot loader. You can pass the kernel parameter from the boot loader as well as you can correct the kernel parameter passing from boot loader from GRUB screen at boot time.

GRUB boot loader configuration file is: /etc/grub.conf

And Correct Configuration is:

default=0

timeout=5

splashimage=(hd0,0)/grub/splash.xpm.gz

hiddenmenu

title Red Hat Enterprise Linux ES (2.6.9-5.EL)

root (hd0,0)

kernel /vmlinuz-2.6.9-5.EL ro root=LABEL=/ rhgb quiet

initrd /initrd-2.6.9-5.EL.img

Probably miss-configured the boot loader, so giving this problem. You can pass the correct parameter from GRUB prompt:

Table 3-3:GRUB Editing Commands

Command

Description

b

Boot the currently listed operating system

d

Delete the current line

e

Edit the current line

o

Create an empty line underneath the current line

O

Create an empty line above the current line

If you know all parameters and sequence of the boot loader you can enter in command prompt also.

Press c on GRUB screen.

Grub>root (hd0,0)

grub>kernel /vmlinuz-2.6.9-5.EL ro root=LABEL=/ rhgb quiet

grub>initrd /initrd-2.6.9-5.EL.img

grub>boot

You should know about the /etc/inittab file, where default runlevel will define. And Much more runlevel specific Scripts are called here.

Actually that problem will occur if you don’t specify the default runlevel.

Reboot the system

Boot the System on single user mode.

Except for a normal boot of Linux, single-user mode is the most commonly used option. This is the system maintenance mode for experienced Linux administrators. It allows you to perform clean backups and restores to any partitions as needed from local hardware. It also allows you to run administration commands, recover or repair password and shadow password files, run filesystem checks, and so forth.

vi /etc/inittab and Write

id:runlevel:initdefault:

Standard Runlevels in RedHat Enterprise Linux

Runlevel

Description

0

Halt

1

Single-user mode, for maintenance (backups/restores) and repairs

2

Multiuser, without networking

3

Multiuser, with networking

4

Unused

5

X11, defaults to a GUI login screen. Logins bring the user to a GUI desktop.

6

Reboot (never set initdefault in /etc/inittab to this value!)

Do the following steps as:

Use fdisk /dev/hdaTo create new partition.

Type nFor New partitions

It will ask for Logical or Primary Partitions. Press l for logical.

It will ask for the Starting Cylinder: Use the Default by pressing Enter Key.

Type the Size: +100MYou can Specify either Last cylinder of Size here.

Press P to verify the partitions lists and remember the partitions name.

Press w to write on partitions table.

Either Reboot or use partprobe command.

Use mkfs –t ext3 /dev/hda?

Or

mke2fs –j /dev/hda? To create ext3 filesystem.

vi /etc/fstab

Write:

/dev/hda?/dataext3defaults0 0

Verify by mounting on current Sessions also:

mount /dev/hda? /data

At exam time read the Lab Scenario carefully. Actually there are two different networks one is 192.168.0.0/24 where your system resides know as example.com domain and another is 192.168.1.0/24 know as cracker.org domain.

One server named sever1.example.com having 192.168.0.254 and 192.168.1.254 is running in your exam. If you make a gateway to that server, you will can ping because IP forwarding is enabled on that server.

1.vi /etc/sysconfing/network

NETWORKING=yes

HOSTNAME=station?.example.com

GATEWAY=192.168.0.254

2.service network restart

Or

1.vi /etc/sysconfig/network-scripts/ifcfg-eth0

DEVICE=eth0

ONBOOT=yes

BOOTPROTO=static

IPADDR=X.X.X.X

NETMASK=X.X.X.X

GATEWAY=192.168.0.254

2.ifdown eth0

3.ifup eth0

Note: If gateway is specified in both file, default gateway takes from interface specific file.

In Network problem think to check:

IP Configuration: use ifconfig command either IP is assigned to interface or not?

Default Gateway is set or not?

Hostname is set or not?

Routing problem is there?

Device Driver Module is loaded or not?

Device is activated or not?

Check In this way:

use ifconfig command and identify which IP is assigned or not.

cat /etc/sysconfig/networkWhat, What is written here. Actually here are these parameters.

NETWORKING=yes or no

GATEWAY=x.x.x.x

HOSTNAME=?

NISDOMAIN=?

Correct the file

Use netconfig command

Either Select Automatically from DHCP or assign the static IP

Use service network restart or start command

Now try to ping it will work.

#vi /etc/resolv.conf

nameserver 172.24.254.254

# dig server1.example.com

#host server1.example.com

DNS is the Domain Name System, which maintains a database that can help your computer translate domain names such as www.redhat.com to IP addresses such as 216.148.218.197. As no individual DNS server is large enough to keep a database for the entire Internet, they can refer requests to other DNS servers.

DNS is based on thenameddaemon, which is built on the BIND (Berkeley Internet Name Domain) package developed through the Internet Software Consortium

Users wants to access by name so DNS will interpret the name into ip address. You need to specify the Address if DNS server in each and every client machine. In Redhat Enterprise Linux, you need to specify the DNS server into /etc/resolv.conf file.

After Specifying the DNS server address, you can verify using host, dig and nslookup commands.