Pass the Nokia SRC Certification 4A0-103 Questions and answers with CertsForce

Viewing page 3 out of 8 pages
Viewing questions 21-30 out of questions
Questions # 21:

An LSP is enabled with one-to-one fast reroute and node protection. What action does the PLR take if node protection cannot be provided?

Options:

A.

The PLR attempts to provide link protection.


B.

The PLR disregards the request after three failed attempts.


C.

The PLR changes the PATH message to request link protection.


D.

The PLR brings down the primary LSP-path.


Expert Solution
Questions # 22:

A router has two admin groups defined (GREEN=1 and RED=3). An interface is associated to both admin groups. What value will be shown in the Admin Group sub-TLV for this interface?

Options:

A.

0x4


B.

0x5


C.

0x10


D.

0xa


Expert Solution
Questions # 23:

Which of the following best describes downstream unsolicited label distribution?

Options:

A.

An LSR may answer requests for label mappings immediately, without waiting for a label mapping from the next-hop.


B.

An LSR may advertise label mappings to all peers for which it might be a next-hop for a given FEC.


C.

An LSR propagates a label mapping downstream for a FEC, only if it has a label mapping for the FEC next-hop.


D.

An LSR will only distribute a label for a FEC when it has been requested to do so.


Expert Solution
Questions # 24:

Click on the exhibit.

Question # 24

An LDP-over-RSVP tunnel is established between routers R1 and R6. There is a VPN service running between routers R1 and R6. Which of the following is TRUE?

Options:

A.

Router R4 swaps both the RSVP-TE LSP label and LDP transport label received with new labels,


B.

Router R4 swaps the VPN service label received with a new label.


C.

Router R4 uses the same RSVP-TE LSP label as the one received from router R3.


D.

Router R4 uses the same LDP transport label as the one received from router R3.


Expert Solution
Questions # 25:

Click on the exhibit.

Question # 25

An LSP traverses the path R1-R2-R3-R6 and facility fast reroute is enabled. If the protected LSP carries one transport label and one service label, how many labels will be on the bypass tunnel if router R2 fails?

Options:

A.

1


B.

2


C.

3


D.

4


Expert Solution
Questions # 26:

Click on the exhibit.

Question # 26

All links have 1Gbps unreserved bandwidth initially and Shared Explicit reservation style is used. After the LSP's primary and standby secondary paths are signaled, how much unreserved bandwidth is left on the links?

Options:

A.

R1-R2 will have 300Mbps left and R2-R4 will have 400Mbps left.


B.

R1-R2 will have 400Mbps left and R2-R4 will have 400Mbps left.


C.

R1-R2 will have 600Mbps left and R2-R4 will have 600Mbps left.


D.

R1-R2 will have 300Mbps left and R2-R4 will have 600Mbps left.


Expert Solution
Questions # 27:

Click on the exhibit.

Question # 27

Initially, all links have 800Mbps of unreserved bandwidth. All links are of equal costs. Shared explicit reservation style is used. LSP 1 is signaled first with a setup and hold priority of 2. Then, LSP 2 is signaled with setup and hold priority of 5. Both LSPs go from R1 to R5. Which of the following is TRUE?

Options:

A.

LSP 1 will follow R1-R3-R4-R5. LSP 2 will follow R1-R2-R5.


B.

LSP1 will follow R1-R2-R5. LSP 2 will follow R1-R3-R4-R5.


C.

Both LSP 1 and LSP 2 will follow R1-R2-R5.


D.

Both LSP 1 and LSP 2 will follow R1-R3-R4-R5.


Expert Solution
Questions # 28:

Click on the exhibit.

Question # 28

RSVP state for LSP 1 has timed out on router R3. Which of the following actions will router R3 initiate to clear the RSVP session?

Options:

A.

Send a RESV Tear message toward router R6.


B.

Send a RESV Tear message toward router R1.


C.

Send a RESV Error message toward router R6.


D.

Send a RESV Error message toward router R1.


Expert Solution
Questions # 29:

Click on the exhibit.

Question # 29

This policy is applied as an LDP export policy. In addition to the FECs learned from its neighbors, which FECs will appear in this router's LIB?

Options:

A.

All FECs with a prefix of 192.168.1.0/30.


B.

Local FECs with a prefix of 192.168.1.0/30.


C.

All FECs excluding 192.168.1.0/30.


D.

Local FECs excluding 192.168.1.0/30.


Expert Solution
Questions # 30:

Which of the following about the use of RRO in fast reroute is FALSE?

Options:

A.

RRO is used to report the protection tunnel status to the head-end router.


B.

RRO contains the MP information that is required by a PLR for facility protection.


C.

RRO contains the label information that is expected by an MP for facility protection.


D.

RRO is used to inform downstream routers about the protection type requested.


Expert Solution
Viewing page 3 out of 8 pages
Viewing questions 21-30 out of questions