Pass the Huawei HCIP-Access H35-211_V2.5 Questions and answers with CertsForce

On Huawei VRP, Advanced IPv4 ACLs (which can match source IP, destination IP, and L4 port numbers) use the 3000–3999 numbering range.

2000–2999 = Basic IPv4 ACL (matches source IP only).

3000–3999 = Advanced IPv4 ACL (matches source/destination IP, protocol, ports).

4000–4999 = Layer 2 (MAC) ACL.

5000–5999 = User-defined/other ranges, not the standard advanced IPv4 range.

Therefore, to match IPs and ports, select 3000–3999.

For IPv4 multicast, the MAC mapping uses 01-00-5E followed by the low-order 23 bits of the multicast IP address. Because an IPv4 multicast address has 28 variable bits (224/4), 5 bits are not mapped to the MAC. Therefore, 2⁵ = 32 distinct multicast IP addresses can map to the same multicast MAC address.

In 10G-EPON (IEEE 802.3av), the wavelength plan uses 1577 nm downstream and 1270 nm upstream. The 1270 nm upstream is used in both asymmetric and symmetric 10G-EPON profiles.

In SIP message correlation, a response matches a request using the CSeq header (method and sequence number) together with the dialog identifiers (Call-ID, From/To with tags). Among the options, CSeq is the direct, standard field used to pair a specific request with its corresponding response within the same dialog.

IEEE 802.3av (10G-EPON) explicitly enables coexistence of 1G-EPON and 10G-EPON on the same outside plant (ODN) by separating downstream wavelengths (1G ~1480–1500 nm vs 10G ~1575–1580 nm) and using dual-rate TDMA in the upstream (10G uses 1260–1280 nm within the broader 1G band). This wavelength plan and OLT capabilities allow operators to reuse existing ODN and achieve a smooth upgrade via WDM overlays at the OLT. Industry and standards materials emphasize this approach for incremental migration.

IPTV over FTTH relies on multicast control; therefore the essential U2000 template is the IGMP template, which defines IGMP behaviors, program authorization binding, and multicast parameters used by the OLT/ONT. MGC applies to voice (VoIP), and SNMP pertains to NMS communication rather than IPTV service logic; value-added templates are not mandatory for basic IPTV.

In Huawei IPTV troubleshooting, mosaic/flash/jerky or intermittent picture typically results from packet loss or bit errors. Common causes include: optical power near the receiver sensitivity threshold causing FEC/BER spikes (A); loss of I-frames (key frames) either in the encoder/compression stage (B) or due to line transmission loss/jitter (D); and device rate-limit (CAR/policing) misconfiguration that drops packets under burst traffic (C). Any of these can yield unstable display.

This is wrong. A PON port LED not green may indicate several states—not only a hardware fault. It can mean the port is administratively shutdown, no ONUs are registered, or the port is in an alarm or idle state depending on the LED color and blinking pattern. Fault requires correlation with alarms and performance counters in U2000, not LED color alone.

In GPON Type C dual-attribution protection, the ONU has dual PON connections to two OLT PON ports (or two OLTs). When the protection group is configured to track the OLT’s uplink Ethernet port, a Down state on that uplink is an OLT-side trigger. The OLT initiates the protection action (forces the working/standby role swap via PON protection signaling).

A — Correct behavior: After the OLT triggers protection, the ONU’s working PON interface becomes standby, and the protect interface becomes working.

B — Correct behavior: The OLT monitors and updates the ONU uplink status as part of the protection group state machine.

C — Correct behavior: After inversion, services egress the ONU via the protect PON port toward the OLT, i.e., traffic follows the configured protect path.

D — Incorrect (answer): In this scenario the trigger is the OLT’s uplink Ethernet status, not an ONU-detected failure. Therefore the ONU does not detect the fault nor initiate the switchover; the OLT does.

(Reference: HCIP-Access V2.5 – GPON protection mechanisms; Huawei OLT protection group behavior, Type C dual-homing with uplink-tracking.)

Huawei devices support independent mapping/remarking for inner and outer VLAN priorities (802.1p CoS) when QinQ is used. Operators can define distinct mapping tables or remark rules per tag. Option A is incorrect (priorities can be derived or remarked, not “must be” tag-in-packet), option C is incorrect because mapping profiles are configurable, and option D confuses VLAN IDs with priorities; inner/outer CoS can be mapped independently for inbound/outbound directions.