1. Home
  2. HP
  3. HPE Technical Certification
  4. HPE0-S59
  5. HPE Compute Solutions Questions and Answers

Pass the HP HPE Technical Certification HPE0-S59 Questions and answers with CertsForce

 HP Exams      Go to Exam Detail      Get Premium Access
Viewing page 2 out of 4 pages
Viewing questions 11-20 out of questions
Questions # 11:

The proposal consists of.

- 3 HPE Synergy 12000 frames

- 6 HPE Composer 2 modules

- 2 HPE Virtual Connect SE 100 GO F32 Module

- 4 HPE Synergy 50 GO interconnect Link Module

Which statements about this proposed design are true? (Select two.)

Options:
A.

The selected interconnect modules do not provide the requested WWN virtualization

B.

HPE Synergy 50Gb ILMs must be replaced with HPE Virtual Connect SE 100 GO F32 modules

C.

The current setup can support up to 18 HPE Synergy 480 Gen10 Plus compute modules

D.

FC upgrade licenses for HPE Virtual Connect SE 100 GbF32 Module must be added

E.

Remove 4 HPE Composer 2 modules from the design, as they are not required

Expert Solution
Questions # 12:

A logical interconnect group can span on multiple HPE Synergy frames for which interconnect type?

Options:
A.

Brocade 32GB Fibre Channel Switch Module for HPE Synergy

B.

HPE virtual Connect SE 32 Gb FC Module for Synergy

C.

HPE Virtual Connect SE 100 Gb F32 Module tor Synergy

D.

HPE Synergy 12 Gb SAS Connection Module

Expert Solution
Questions # 13:

Your customer reports mat an external FC boot volume for Windows server is visible four times in the Disk Management 1 online and 3 offline.

What should you do to resolve this issue?

Options:
A.

Disable deduplication for this volume at the array level

B.

Remove the offline disks using array management tools

C.

Install and configure MPIO on me Windows system

D.

Remove the offline disks using Windows Disk Management

Expert Solution
Questions # 14:

Which statement about port flap protection is true?

Options:
A.

It can disable link aggregation groups or stacking ports that have gone down and come up in quick succession.

B.

It allows an administrator to suppress excessive inbound multicast, broadcast, and DLF packets.

C.

It allows configuration of hardware Layer 2 switching behavior of multicast traffic to optimize network resource usage.

D.

It allows the creation of LACP groups on the upstream switch that span multiple HPE Synergy Virtual Connect modules.

Expert Solution
Questions # 15:

Refer to Exhibit:

Question # 15

Your customer plans to update the firmware for the logical interconnect shown.

Based on the information in the exhibit, which statement about network connectivity is true?

Options:
A.

Only the manual orchestration method will allow a firmware upgrade without causing network downtime.

B.

It is possible to update this logical interconnect without network downtime if orchestrated method is used.

C.

Compute nodes will experience network downtime if the Force option is selected, as it will enforce parallel update.

D.

Compute nodes will experience network downtime not longer than 1 minute regardless of the orchestration method.

Expert Solution
Questions # 16:

Your customer changed the storage pool state from managed to discovered.

What is the impact of that change?

Options:
A.

This storage pool can be deleted using HPE OneView interface.

B.

All volumes from that pool will be removed from HPE OneView.

C.

Volume provisioning will be disabled for that storage pool.

D.

Storage pool parameters cannot be modified using HPE OneView.

Expert Solution
Questions # 17:

What is a restriction of using a RoCE network?

Options:
A.

It is by default configured as an untagged network and cannot be a part of a network set.

B.

It does not support Private VLAN and Multicast VLAN.

C.

it is not supported with HPE Virtual Connect SE 40 GD F8 Module for HPE Synergy.

D.

It does not support smart link and private network features.

Expert Solution
Questions # 18:

Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has the appropriate storage controller installed and two 12Gb SAS switches installed in the first fabric.

The customer reports that the compute nodes cannot access the storage module.

What will you verify first when troubleshooting this problem?

Options:
A.

If the SAS logical interconnect is a part of the logical enclosure and has a healthy state.

B.

If the D3940 module is imported in a managed state that allows volume provisioning.

C.

If there is at least one iSCSI network configured that will provide access to the module.

D.

If the D3940 storage module is properly licensed through the HPE OneView interface.

Expert Solution
Questions # 19:

An administrator tries to open iLO interlace from HPE OneView Instead of being automatically logged in a login prompt displays

Where should you start the troubleshooting process?

Options:
A.

At the iLO interface to verify whether the ILO Advanced license is properly applied

B.

At HPE OneView Interface to verify whether the server is In the maintenance mode

C.

At the iLO interface to verify whether the SSO certificate is removed from an iLO.

D.

At HPE OneView Interface to verify whether the iLO processor is disabled

Expert Solution
Questions # 20:

Your customer has experience with utilization sampling for HPE Virtual Connect SE 100 Gb F32 Module for HPE Synergy. They have recently purchased HPE VC FC modules.

What must you be aware of regarding utilization sampling for the new modules?

Options:
A.

Utilization sampling for HPE VC FC modules must be enabled manually using CLI.

B.

For HPE VC FC modules, utilization sampling is always enabled and cannot be disabled

C.

For HPE VC FC modules, utilization sampling can be enabled once appropriate license is applied

D.

Utilization sampling works the same way tor any type of HPE Synergy interconnect modules

Expert Solution
Viewing page 2 out of 4 pages
Viewing questions 11-20 out of questions